Whirlpool Refrigerator Ice Maker & Related

This ice maker cover fits over the ice maker head to protect the control module and moving parts inside your freezer. Replacing a cracked or missing cover helps prevent frost intrusion and restores a clean, finished look.

• Shields the ice maker mechanism from debris and moisture
• Helps maintain airflow to reduce frost at the ice maker face
• Replaces a cracked, warped, or missing cover with broken tabs
• Can help address exposed gears/wiring or rattling from a loose cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the front of the ice maker
• Release retaining tabs or screws and remove the old cover
• Align and snap the new cover fully into place; verify it's secure and clear of moving parts

This ice storage bin holds the ice made by your refrigerator's icemaker and keeps it contained and easy to access in the freezer. Replace a cracked or warped bin to prevent spills, jams, and poor seating.

• Collects and stores ice cubes produced by the icemaker
• Keeps cubes contained to minimize spills and stray frost
• Slides/seats on the designated rails or shelf area in the freezer
• Common signs of failure: cracks, broken tabs, bin won't seat or slides out, ice falling into the freezer

• Unplug the refrigerator or disconnect power; switch the icemaker off
• Pull the old bin straight out; empty and clean the area
• Slide the new bin in until fully seated; restore power and turn the icemaker back on

By Whirlpool. For porcelain liner Whirlpool, Kitchen Aid, Roper, Estate and Kenmore (with model prefix 106) refrigerator models with 30, 33 and 36 inch wide cabinets. Incorporates round plug. Kit includes wiring harness, fill tubes, water valve, ice bin, hardware and instructions.

This refrigerator ice maker assembly automatically freezes water and harvests cubes so you have a steady supply of ice in the freezer. Replacing a failed assembly restores consistent, hands-off ice production.

• Freezes water in the mold and ejects cubes on a controlled cycle
• Signals the water inlet valve to refill after each harvest
• Pauses production when the bin is full via the unit's shutoff mechanism
• Common signs of failure: no ice production, won't eject or refill, intermittent cycling, or very small/hollow cubes

• Unplug the refrigerator and shut off the water supply before servicing
• Take photos of wiring and mounting to match connections and positions during reassembly
• Reuse any model-specific brackets or covers from the original unit if required
• After installation, restore power/water and allow several hours for the first batches

This small plastic control arm extension links to the mechanism it serves, restoring proper movement and engagement so the appliance can operate as intended. It's a simple, direct-replacement component designed to snap in and align correctly.

• Connects to the existing control arm to extend its reach and function
• Helps correct issues like improper engagement or intermittent operation
• Can address symptoms such as sticking, misalignment, or failure to activate
• Sized to fit the original mounting points for consistent motion

• Disconnect power (and water if applicable) before servicing
• Note the orientation of the original part to match during reassembly
• Inspect the mating control arm and linkage for wear or damage
• Test operation before fully reassembling panels or covers

The Ice Maker Scoop is an OEM component specifically designed for Whirlpool ice machines. As an included accessory, it provides a sanitary and convenient way for users to fetch ice from the storage bin.

The scoop is strategically designed with an ergonomic handle and wide opening bowl shape. This facilitates easy scooping and transport of ice cubes without spillage or crumbling. Its food-safe materials maintain hygienic conditions in the storage area. 

Symptoms of a faulty scoop include:

• Cracks or breaks that compromise the scooping surface 
• Leaks or spills of ice when trying to scoop
• Sharp edges that risk cuts or scratches
• Warping or loosening of the handle attachment over time

This OEM Whirlpool scoop is also compatible with some Scotsman and Manitowoc ice machines. Replace yours today to restore safe and hygienic ice retrieval from the storage bin.
 

The Icemaker is an OEM part for Whirlpool refrigerators. It automatically produces batches of ice using a water inlet and freeze cycle.

Causes can be failures in the temperature probe, water valve, ejection mechanism, or freezing compartment. Mineral buildup from hard water reduces efficiency over many harvest cycles as well.

Symptoms of a bad ice maker include:

• No ice production or low ice yields over time
• Ice cubes appearing cloudy or improperly formed
• Leaking or dripping water inside the freezer
• Clicking or grinding noises during operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement ice bin stores the ice produced by your refrigerator's icemaker and fits into its designated compartment for easy access. Replace a cracked or warped container to restore reliable ice storage and smooth dispensing.

• Holds harvested ice until use
• Guides cubes toward the dispenser outlet
• Restores proper fit when the original bin is cracked, broken, or warped
• Common symptoms: ice won't dispense or jams; ice spills into the freezer; bin won't seat or latch properly

• Unplug the refrigerator or disconnect power before servicing
• Empty and remove the old bin from the compartment
• Align and slide the new bin into position until fully seated
• Restore power and allow time for new ice to accumulate

This coupling is the small connector that links a drive motor to its mating component, transferring rotation so the appliance operates smoothly. Replacing a cracked or stripped coupling restores reliable drive and helps prevent further wear.

• Connects the motor shaft to the driven part to transmit torque
• Maintains alignment to reduce wobble and slippage
• Failure signs can include no movement, intermittent operation, clicking/grinding, or visible cracks/rounding
• Restores consistent motion of the connected part once replaced

• Disconnect power (and shut off water/gas if applicable) before servicing
• Access the drive area and remove any covers/tray/drive components as needed
• Pull the old coupling straight off the keyed or D-shaped shaft; clean and inspect the shaft
• Align and press the new coupling fully onto the shaft, reassemble, and test

This ice maker assembly replaces the complete cube-making unit in your refrigerator. It restores automatic freezing, harvesting, and bin-level shutoff so your appliance can reliably produce a steady supply of ice again.

• Freezes water in the mold and ejects cubes into the ice bin during each harvest cycle
• Pauses production when the bin is full via the built-in shutoff mechanism
• Typical failure symptoms: no ice production, cubes not ejecting or stuck mid-cycle, intermittent clicking/grinding from the module
• Can replace a cracked or seized ice mold assembly that jams or leaks at the icemaker

• Disconnect power and shut off the refrigerator's water supply before servicing
• Remove the ice bin; loosen mounting screws and unplug the wire harness to release the old unit
• Transfer any mounting brackets or covers from the original unit if needed; reuse existing hardware
• Restore power and water; ensure the fill tube is clear and allow the icemaker to begin cycling

This ice container assembly catches and stores ice from the icemaker so you have a ready supply on hand. It replaces a cracked, missing, or damaged bin to keep ice contained and feeding properly. What it does:

• Collects and holds ice produced by the icemaker to prevent spilling inside the freezer.
• Guides ice toward the dispenser or access area for reliable dispensing/storage.
• Replaces bins that are cracked, warped, or no longer securing ice properly.
• Helps prevent ice from falling onto shelves or into other compartments.

• Disconnect power to the refrigerator before servicing to avoid injury.
• Remove any remaining ice and shelves that block access before replacing the bin.
• Slide the new bin into the tracks or mounting points until it seats securely.

This ice container assembly collects and stores cubed ice produced by the freezer's ice maker, keeping ice contained and ready for dispensing or manual use. Durable molded design fits into the ice maker cavity and funnels ice into the dispenser area. What it does:

• Holds and contains ice made by the ice maker so ice stays organized and accessible
• Guides ice toward the dispenser or auger, helping ensure consistent flow
• Replaces cracked, warped, or damaged containers that cause ice jams or leaks
• Helps reduce spillage when removing or emptying the ice bucket

• Disconnect power to the refrigerator before beginning service
• Empty ice from the bucket and remove any loose ice before removal
• Handle the molded plastic carefully to avoid cracking; install until it seats securely

This replacement ice cube tray is a direct-fit plastic tray designed to hold and release ice cubes in compatible top- or bottom-freezer refrigerators. Restores convenient ice storage and simple manual ice removal. What it does:

• Holds water in separate cavities so ice cubes form evenly.
• Flexes slightly for easier ice release to reduce twisting or chipping.
• Replaces cracked, warped, or missing trays that cause leaking or uneven freezing.
• Helps prevent contamination from freezer debris when used as intended.

• Remove old tray and wipe area clean before installing the new tray.
• Fill tray with water on a level surface and place flat in the freezer to freeze.
• Handle carefully when removing ice to avoid spills; do not force with sharp tools.
• Clean tray before first use and as needed; follow refrigerator manufacturer's care guidance.

The Ice Maker Field Install Kit is an OEM replacement part for Whirlpool side-by-side (SXS) refrigerators. This kit provides all the components necessary to add or replace an ice maker in compatible refrigerator models. It is designed to produce a steady supply of ice cubes, enhancing convenience and functionality for users.

Symptoms of a bad Ice Maker or the need for installation include:

• Ice maker not producing ice or producing insufficient quantities
• Leaks or water pooling near the ice maker
• Loud or unusual noises during operation
• Visible damage or wear to the ice maker components

Causes of a malfunctioning Ice Maker can include mineral buildup from hard water, wear on internal components like the motor or ejector blades, or issues with the water supply line. Regular maintenance and proper installation help extend its lifespan.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Ice Maker is an OEM part for Whirlpool bottom freezer refrigerators. Located inside the fresh food door compartment, it is designed to automatically produce batches of ice to ensure plenty of chilled water, drinks, and snacks. This ice maker features adjustable settings to meet daily needs.

Symptoms of a failing ice maker may include:

• Reduced ice production or intermittent cubes   
• Ice clumping together instead of separate pieces
• Ice maker mechanism continually running

Causes relate to normal wear of moving parts over years of use among harsh temperature fluctuations inside the fresh food door. Mineral buildup can also interfere with sensitive components.  

This OEM Whirlpool replacement fits many Whirlpool, KitchenAid, and other major brand refrigerators.