Whirlpool Refrigerator Parts

Ordered new gaskets from Appliance Parts Pros, arrived in 4 days. Removed old gaskets and replaced by starting at top corner and. Pushing seal into slot. Day before, opened seal boxes and spread seals to smooth out. Took about 10 minutes to replace both door seals. Right door magnetic seal improved but not great. Adjusted level and installed a 1/16” washer in door bottom hinge, which leveled door better and improved the seal strength. Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

• Ice maker won't dispense ice
• Ice maker not making ice

After finding out the cost that we would have to pay for the repair locally, I went to Appliance parts pro.com. with the intention of finding out the cost for parts. We had been quoted $100 for the first hour which included repair if it could be done under the first hour plus parts. And they added that the typical repair for the ice maker was between $200 and $500. Fortunately we are very organized and had the original paperwork of the refrigerator which has all parts and numbers for the... Read more

I replaced the light fixture in 5 minutes. Been working well. Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

First Problem - WATER INLET VALVE - After having problems with ice maker not making ice, I troubleshot and replaced the water inlet valve. Video and instructions were excellent. With 16 year old fridge, the water lines had compression fittings in the old valve, so had to cut the fittings off with a razor blade to allow the lines to insert into the new valve press-in type fittings. Worked great / no leaks at the new valve. But, new leaks occurred at the water filter housing spraying down into... Read more

Replaced Read more

• Ice maker dispenses too little ice
• Not dispensing water
• Touchpad does not respond
• Leaking

I'm such a pro, I figured I needed a new hose for my water dispenser so I ordered it. When it arrived I called my handyman. He told me I did not need a hose I needed A cartridge. So I had to return the hose and order the cartridge! Your company was so cooperative and made the return so easy Thank you! Next time I call the handyman first! Read more

• Leaking

Replaced both inlet valves, no joy. Upon further inspection, found ice maker harness extremely tight at lower freezer door hinge, clamped in place right at a pivot point. Essentially the harness is held in place and rotates with the door. 6 wires broken inside. Splice repair and ice maker now works. Most likely will have to replace harness eventually. Unless there is more slack inside the freezer door this will probably happen again. Very poor design. Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

• Fridge too cold
• Freezer too cold
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

Did some online research and everything pointed to the fact that moisture was getting into the freezer and therefore the seal was not doing it's job. I ran my finger along the seal and sure enough I detected cold air coming out of one corner of the seal. I ordered the appropriate part from Appliance Parts Pros (APP) but decided to test my diagnosis by installing thin weather stripping in the affected area. I checked the freezer the next day and saw no accumulation of any more Rime ice so... Read more

Ordered parts from Appliance Parts Pros. Made sure they fit using the model number link. Was a great experience, fast shipping. Read more

After taking the two vegetable drawers out from above, the glass shelf, the pantry drawer and the cross support for the glass, you can get to the two recessed hex head screws holding the end cap. You will need to transfer the metal drawer slide to the new cap, but it doesn't need to come off first. When the end cap is loose, gently rotate it toward the front. Once the humidity control slide is at 90 degrees from the back of the refrigerator, the tab holding it in place will slip out easily.... Read more

It was an extremely easy fix with this video https://www.youtube.com/watch?v=l2YpWoE-BUA Read more

• Noisy
• Fridge runs too long
• Fridge too warm
• Freezer section too warm

Unplugged refrigerator and removed access panel from back of fridge. Have had this panel off many times for dust removal. Panel is a cheap piece of glorified cardboard on this Whirlpool model, which is a shame given that it was a $1000 refrigerator. Fan motor is mounted on stamped sheet metal bracket which I removed from cabinet with old fan attached to it. Metal bracket held in place by 4 1/4 inch hex head sheet metal screws. Two outermost screws can be removed with nut driver but access to... Read more