Whirlpool Tube Or Fitting

This gas tubing is a direct-fit replacement line that routes gas between components and restores a secure fuel path for safe burner operation. It helps stop leaks and ensure consistent gas flow to the appliance. What it does

• Replaces damaged, cracked, or corroded gas tubing that can cause leaks or loss of gas flow
• Restores a sealed connection between the gas valve and burner or between gas components
• Can resolve symptoms such as gas odor, intermittent ignition, or weak burner flame when tubing is the cause
• Designed to match OEM form and fit for straightforward replacement when listed for your model

• One gas tubing assembly as shown

• Shut off the gas supply and unplug the appliance before starting any work
• After installation, test all fittings with a leak detection solution; do not use an open flame
• Follow all local codes and OEM instructions for fittings, sealants, and torque values

This gas tubing supplies gas from the oven manifold to the burner assembly, restoring a safe, direct fuel path for proper ignition and heating. Use when tubing is cracked, corroded, kinked, or leaking. What it does:

• Carries gas from the appliance's manifold or valve to the burner(s)
• Maintains a sealed, flexible connection to allow component movement
• Replaces damaged, corroded, or pinched tubing that can cause leaks or poor ignition
• Helps restore consistent burner performance and proper heating when tubing is compromised

• Turn off gas supply and electrical power before starting any service
• Verify correct orientation and secure fittings to avoid leaks; use OEM-specified fittings and torque
• Leak-test all connections with a soap solution or approved leak detector before returning appliance to service

This gas tubing replacement routes fuel between the appliance gas manifold and control valve to restore safe, reliable fuel delivery. Use it when tubing is damaged, corroded, or leaking to help eliminate gas leaks and restore normal burner operation. What it does:

• Channels natural gas or LP from the manifold to the valve and burners for ignition
• Replaces cracked, corroded, or kinked tubing that can cause leaks
• Addresses symptoms like a gas smell near the appliance, burners that won't light, or intermittent flame
• Keeps fuel flow consistent so burners heat predictably when controls are on

• Shut off the appliance gas supply and disconnect power before starting work
• Tighten fittings to manufacturer torque; check all connections for leaks with a soap solution or approved gas leak detector
• If you smell gas during or after installation, stop and ventilate the area.

This replacement fitting connects the appliance's water line to its internal plumbing so water flows where it's needed and stays sealed. It restores a proper watertight connection to help stop leaks and ensure reliable water delivery. What it does:

• Connects the external water supply line to the appliance's internal water inlet
• Creates a secure, watertight seal to prevent drips and leaks at the connection point
• Supports consistent water flow for ice makers, dispensers, or valves where used
• Can resolve symptoms like visible leaks, reduced water flow, or intermittent filling

• One replacement fitting

• Turn off the water supply and unplug the appliance before installing
• Inspect mating surfaces and replace any damaged O-rings or gaskets as needed
• Hand-tighten first, then snug with appropriate tools; avoid over-tightening
• If plumbing sealant is recommended by your installer, use plumber's tape on threaded connections only

Location: Left rear & left front.

Location: Right front. Gas valve tubing.

This fitting tube connects a section of appliance tubing to the service plumbing to restore a sealed fluid path and prevent leaks. It's a direct-replacement plumbing fitting used where small-diameter tubing joins a fixed port. What it does

• Forms a secure connection between tubing and a plumbing port to maintain water/condensate flow
• Stops symptoms like visible leaks, pooling water, or reduced fill/drain performance when the original fitting is damaged
• Provides the proper interface for OEM tubing size and routing in the appliance
• Helps restore normal operation without altering factory plumbing

• One fitting tube

• Disconnect power and shut off water supply before servicing
• Drain remaining water from lines to reduce mess and pressure before removing old fitting
• Hand-start fittings then tighten to OEM torque; avoid over-tightening which can crack ports or tubing
• Inspect connections for leaks after restoring water and power; re-tighten if needed