Yard Machines Parts

Variable speed drive belt connects engine to transmission for lawn tractors and riding mowers. Replace if stretched, damaged, or broken. Verify fit with your model.

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

Deck belt cover for riding mowers with 42-inch decks. Shields the belt assembly from debris and damage. Replace if cracked, broken, or missing.

Scraper blade installs at the base of your snow blower housing to clear snow down to pavement. Replace if worn, cracked, or missing bolts are exposed.

Shoulder spacer for lawn tractors and riding mowers. Installs to maintain proper spacing between components. Replace if worn, damaged, or missing.

This bearing flange is used on a wide variety of lawnmowers and lawn tractors. Unlike other bearings, the flange bearing is used to ensure the axle assembly stays securely attached to the pivot axle. The purpose of the flange bearing is to make sure the axle is able to move freely and in an effortless manner. The bearing undergoes a large amount of friction and stress while in use, so it can start to wear down.If the lawnmower is showing signs of wear at the flange bearing, it should be replaced. It's a good idea to regularly inspect the part to be sure it is in good shape. To replace the flange bearing, remove the bolt from the steering shaft and remove the old bearing. Grease the new bearing and the shaft before reinstalling the part. Reassemble and tighten all parts.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The flange bearing is made to be compatible with lawnmowers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

Snowblower not clearing snow properly? Worn rubber paddles reduce snow removal efficiency. This auger paddle kit restores clearing power in about 30 minutes.

Auger not turning or moving slowly? This snowblower worm gear connects the driveshaft to auger blades. Moderate DIY repair restores snow ejection.

Speed select cable for snowblower ground drive system. Replace if your cable is deteriorated, damaged, detached, or missing from the control assembly.

Carburetor gasket seals the air intake system on lawn mowers and tractors. Replace if you notice air leaks, rough idling, or poor engine performance.

Carburetor insulator gasket seals the connection between carburetor and engine. Replace if worn, cracked, or causing air leaks and poor performance.

Hinged mulch plug assembly for walk-behind lawn mowers. Replaces worn or broken mulch covers. Includes metal hinge. Installs in place of discharge chute.

This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

Mower vibrating excessively or blade loosening? This blade adapter connects the motor shaft to the mower blade. Simple DIY repair, typically 15 minutes.

Foam air filter for tillers and cultivators. Replace when dirty or damaged to maintain proper fuel-air balance for engine performance. Verify fit.