Yard Machines Trimmer

This is a ratchet pawl assembly used in the recoil starter mechanism of a string trimmer. It engages the starter pulley to turn the engine over when the pull cord is yanked. Replace this part if the pull cord pulls freely without engaging the engine or if the trimmer fails to start due to a slipping or broken starter pawl.

Blade guard assembly for line trimmers. Protects operator from debris and rotating components. Replace if cracked, broken, or missing for safe operation.

Fastener hardware set for line trimmers. Replace missing, stripped, or damaged screws and nuts that secure internal components. Sold as individual set.

Engine o-ring gasket creates a compression seal between engine components to prevent oil and fluid leaks. Replace when worn or cracked. Verify fit with your model.

O-ring gasket creates a seal to prevent fluid and gas leaks in tillers and lawn equipment. Replace when cracked, brittle, or leaking. Verify fit.

This flywheel is an authentic OEM replacement part sourced directly from the manufacturer. It is part of the starter assembly on trimmers and other small engines that use a pull-start system. If the engine is misfiring, overheating, or not starting, the flywheel should be checked and replaced if necessary. Normal wear and tear can lead to the breakdown of the flywheel. The flywheel is located behind the recoil starter assembly and is attached to the engine. When the starter cord is pulled, the flywheel spins to start the engine. If the flywheel is damaged and doesn't spin fully or is seized and won't spin at all, it should be replaced. A Phillips screwdriver, spark plug wrench, Torx wrench, long-nosed pliers, and a rubber hammer are needed to complete this project. A bowl or other receptacle for storing drained fuel and work gloves are also suggested. Make sure the engine is cool, and the spark plug is removed before making this repair.This flywheel is a solid metal part that is sold individually. This flywheel is designed for tillers, cultivators, and other small engines manufactured by Craftsman and Troy-Bilt.

Replace a cracked or missing starter guard that leaves the recoil mechanism exposed. Snaps into place in minutes with basic hand tools.

This flywheel assembly mounts on the engine crankshaft of a gas-powered line trimmer and provides the rotational mass needed to keep the engine running smoothly between power strokes. It also drives the ignition system by passing magnets over the ignition coil to generate spark. Replace this flywheel if the engine has no spark, runs erratically, or if the flywheel is cracked, has damaged magnets, or a sheared keyway.

This replacement part is an o-ring. It is a genuine replacement part made by MTD. O-rings are small but are a very important part of many appliances. These rubber rings are placed around parts that have spaces in their vicinity. This blockage created by the O-ring allows gas and air to stay within the engine or appliance. Otherwise, it might escape and cause issues during use. A new o-ring might be needed if the current ones are missing or becoming thin. This is common in many appliances. If there is a noticeable amount of air or gas escaping the appliance then it might be caused by a gap where an o-ring should be. This o-ring is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM part sourced directly from the manufacturer.

Fix a trimmer that won't start with this complete starter housing assembly. Includes housing, pulley, spring, rope and grip for easy pull-start.

Replace a cracked or broken blade guard that no longer protects you from spinning line and debris. Direct fit for multiple trimmer models.

Engine runs but trimmer head won't spin? This lower drive shaft assembly houses the driveshaft that transfers power to the cutting head on gas trimmers.

Ignition coil module assembly for gas string trimmers. Mounts to engine block and connects to spark plug. Replace if cracked, damaged, or contacts are worn.

Replace a seized or damaged 25cc short block assembly in your gas trimmer. Includes cylinder, piston, and crankshaft for 2-cycle handheld engines.

This short block assembly is a genuine MTD part, sold individually. This short block assembly can be used as a replacement part for a string trimmer, a tiller, or an edger. The short block includes the crankshaft, piston, rod, camshaft, valves, and governor. A short block assembly might be necessary if there is damage to a wide range of parts in the equipment's engine. Check for frequent stalling, misfires, or an inability to power on. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This short block assembly is compatible with the following brands: MTD, Craftsman, and Cub Cadet.