Parts for Electrolux CASE7074NA3: 02 - Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

One per package.

Control panel cover for dryers. Replaces cracked, broken, or missing covers that expose internal components. Installs on the console housing assembly.

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

Replacement air duct assembly with mesh screen for dryers. Installs between drum and heater. Replace if screen is burnt, cracked, melted, or missing.

Foam insulator strip that cushions dryer panels and reduces vibration. Replace if worn, compressed, or missing to maintain quiet operation and fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This is a felt seal that wraps around the dryer drum to create a soft barrier between the drum and the dryer housing. It helps maintain proper airflow and prevents clothes from getting caught between the drum and the cabinet. Replace this seal if you notice clothes snagging, hear squealing or scraping noises during tumbling, or find lint escaping around the drum edges.

This moisture sensor consists of two metal strips typically mounted inside the dryer drum area that detect the moisture level in clothing during a drying cycle. It signals the control board to end the cycle when clothes reach the desired dryness. Replace this sensor if your dryer shuts off too early with clothes still damp, runs too long, or if the auto-dry cycle no longer functions properly.

Mounting bracket for dryer installation and support. Secures dryer components in place. Replace if bracket is cracked, bent, broken, or missing.

This is the main electronic control board that manages all dryer functions including cycle selection, timing, and temperature regulation. It receives input from the user interface and sensors, then directs power to the appropriate components such as the motor, heater, and moisture sensor. Replace this board if the dryer fails to start, stops mid-cycle, displays error codes, or buttons and cycle selections no longer respond properly.

Replacement base for your dryer. Supports the cabinet and internal components. Needed when original is cracked, rusted, or structurally damaged.

Mounting bracket for dryer installation. Secures components in place during operation. Replace if bent, cracked, or missing to ensure proper alignment.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Steam hose kit connects water source to dryer steam system. Includes rubber fill hoses and Y connector. Replace if hoses are cracked or leaking.

Fixes steam cycle not working or water not entering drum during steam cycles. Controls water flow into dryer. Moderate DIY repair for steam dryers.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

Rubber grommet cushions wiring, tubes, or panels in your dryer. Replace if cracked, worn, or missing to prevent chafing and reduce vibration noise.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

Wire harness that connects control board, sensors, and electrical components in your dryer. Replace if wires are damaged, connectors are broken, or worn.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.