Parts for Maytag MLE2000AYW: 02 - Cabinet-Front (Dryer) Parts

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This terminal block provides the electrical connection point between the washer's power cord and the appliance wiring, restoring a secure, stable supply for safe operation. It replaces a damaged or corroded connection assembly. What it does

• Secures and insulates power cord wires where they enter the washer to prevent loose connections and arcing
• Restores reliable incoming power when a burned, loose, or broken terminal causes intermittent power or no power
• Helps prevent electrical resistance and heat buildup at the cord connection
• Matches OEM mounting and terminal layout for a direct replacement

• One terminal block assembly as shown

• Disconnect the washer from power before servicing to avoid shock or injury
• Inspect wire colors and terminal positions, then transfer wires to the same terminals on the replacement part
• Typical installation requires basic hand tools (screwdriver, nut driver); some models may need partial cabinet access
• If you see melted insulation or other wiring damage, replace affected wiring.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Size: 10-32 inch.

Specs: 7/32 INCH

This terminal block connects the appliance to household power, providing a secure point for the incoming power cord wires. Replacing a damaged terminal block restores a solid electrical connection and reduces fire risk. What it does:

• Secures and organizes incoming power cord wires to the appliance's internal wiring
• Provides stable electrical contact for consistent power delivery
• Prevents loose or arcing connections that can cause intermittent power or overheating
• Common symptoms: appliance won't power on, intermittent power loss, visible burning or melted plastic at the power entry point

• Disconnect power at the breaker and verify the appliance is de-energized before starting
• Confirm wire placement and tightness; replace any scorched or damaged wiring or connectors
• Use proper tools and follow the appliance wiring diagram; tighten terminal screws to manufacturer torque if specified

This terminal block provides the electrical connection point between the washer's power cord and the appliance wiring, restoring a secure, stable supply for safe operation. It replaces a damaged or corroded connection assembly. What it does

• Secures and insulates power cord wires where they enter the washer to prevent loose connections and arcing
• Restores reliable incoming power when a burned, loose, or broken terminal causes intermittent power or no power
• Helps prevent electrical resistance and heat buildup at the cord connection
• Matches OEM mounting and terminal layout for a direct replacement

• One terminal block assembly as shown

• Disconnect the washer from power before servicing to avoid shock or injury
• Inspect wire colors and terminal positions, then transfer wires to the same terminals on the replacement part
• Typical installation requires basic hand tools (screwdriver, nut driver); some models may need partial cabinet access
• If you see melted insulation or other wiring damage, replace affected wiring.

Color: White

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts

Specs: 10 - 16 x .375

This ground screw secures the appliance grounding conductor to the chassis for a reliable electrical ground connection, helping maintain safety and proper operation. It's a direct-fit fastener used where a dedicated ground screw is required. What it does

• Fastens the grounding conductor to the appliance frame to maintain a secure earth/ground connection.
• Helps prevent electrical shock and reduces risk of stray voltage on the chassis.
• Addresses symptoms like intermittent or absent grounding and loose or corroded ground connections.
• Used wherever the original equipment grounding screw has been lost, damaged, or corroded.

• Disconnect power at the breaker and unplug the appliance before starting any work.
• Only attach to designated grounding points on the chassis; ensure the mating surface is clean and free of paint or corrosion.
• Use the correct driver and moderate hand torque—do not overtighten to avoid stripping threads.

This relay is used on multiple types of appliances: Ranges, Cooktops, Wall Ovens, Washers and Dryers.

Spesc: #12 pozi - drive

This machine control board is the washer's electronic brain, directing the motor, water valves, and cycle timing. Replacing a failed board restores proper control of wash, rinse, and spin functions and helps resolve erratic or non-starting cycles.

• Coordinates cycle timing and sends power to the drive motor, drain pump, and fill valves
• Monitors inputs from the door lock and sensors to manage operation
• Failure can cause the washer not to start, stop mid-cycle, or fail to spin or drain
• Associated with control-related error codes or intermittent operation

• Disconnect power to the appliance before servicing
• Handle the board by the edges and use ESD protection to avoid static damage
• Label or photograph wiring; move connectors to the new board one at a time and verify ribbon-cable orientation
• Mount securely and ensure all harnesses are fully seated before restoring power and running diagnostics per the tech sheet