Parts for Maytag MLE2000AYW: 03 - Cabinet-Front (Washer) Parts

Specs: No.8X1/2 HEX WASHER HEAD

Specs: 10 - 16 x .375

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This pressure switch senses and signals the washer's water level so the machine fills and cycles correctly. Replacing a failing switch restores accurate water-level sensing for consistent wash performance. What it does:

• Monitors tub water level and signals the control board to start/stop filling.
• Helps the washer advance through fill, agitate, and drain cycles based on detected water height.
• Common symptom: washer overfills, underfills, or fails to advance cycles.
• Works with existing pressure hose and wiring harness to relay air pressure changes.

• Disconnect power and water to the appliance before beginning any work.
• Note and photograph hose and wiring positions before removal to ensure correct reinstallation.
• Inspect or replace the small pressure hose if cracked or clogged; ensure a tight, leak-free connection.

This cabinet spring secures the appliance cabinet to the frame to control movement and vibration. Replacing a fatigued or broken spring restores cabinet stability and helps reduce rattling and excessive shaking during operation.

• Anchors the cabinet to the chassis to maintain proper alignment
• Helps limit vibration and noise during use
• Supports correct fit of cabinet panels and top
• Typical failure signs: loose or shifting cabinet, rattling, or increased vibration

• Disconnect power before servicing; allow all moving parts to stop
• Support the cabinet or panel to relieve spring tension before removal
• Spring is under tension—use suitable pliers/spring tool and wear eye protection and gloves
• After reassembly, verify the cabinet is level and securely fastened

Color: White

Color: White This part has been discontinued and is no longer available.

This clip is a small retaining fastener used to secure components inside your appliance, keeping parts aligned and in place during operation. Replacing a worn or missing clip helps stop looseness, vibration, and premature wear.

• Holds a designated part firmly to its mating surface
• Maintains proper alignment to reduce rattling and shifting during cycles
• Symptoms of failure: parts that won't stay attached, misalignment, buzzing/rattling noises, or a visibly bent/missing clip
• Restores a secure, factory-style fit

• Disconnect power; turn off water supply before servicing
• Note the original clip position and orientation (a quick photo helps)
• Use needle-nose pliers to release/install; avoid over-bending the clip
• Ensure the component is fully seated and secure before reassembly and testing

This spring support secures a suspension spring to the washer's frame, helping keep the tub stable during wash and spin. Replacing a damaged support restores proper balance control to reduce vibration and banging. What it does:

• Anchors a suspension/tub spring to the cabinet or base
• Helps control tub movement and maintain alignment during spin
• Failure can cause excessive vibration, banging, off-balance shutdowns, or a leaning tub
• Visible cracks, bent tabs, or a detached spring indicate the support needs replacement

• 1 spring support

• Disconnect power and turn off water before servicing
• Support the tub and carefully relieve spring tension before removing the old support
• Transfer the spring to the new support and install in the original location/orientation
• Wear gloves and eye protection; springs are under tension

Spesc: #12 pozi - drive

Specs: 10 - 16 x .375

Specs: 10 - 16 x .375

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

A small replacement clip that secures the dispenser hose to the dispenser assembly, helping keep the hose seated and reducing the chance of leaks or disconnection. Simple, durable part for restoring proper hose retention. What it does:

• Holds the dispenser/hose connection firmly in place to prevent the hose from slipping free
• Helps reduce water leaks and intermittent dispenser flow caused by a loose hose
• Keeps hose routing stable to avoid rubbing or wear against nearby components
• Works with the dispenser assembly to maintain proper alignment and seal

• One retainer as shown

• Disconnect power and water supply before starting any repair
• Access the dispenser area per your appliance's service instructions; remove trim or panels if required
• Snap the retainer over the hose at the dispenser connection until it seats; verify the hose is fully seated
• If you see damage to the hose or fittings, replace those parts before finishing