Parts for Maytag MLE2000AYW: 09 - Door Shroud & Door Latch Assembly (Wash) Parts

A replacement latch spring that helps the appliance door latch return and hold securely, restoring reliable door engagement and proper cycle starts. Fits the original latch mechanism and installs quickly for common latch-related issues. What it does:

• Provides tension for the door latch so the strike stays engaged during operation
• Restores proper door closing and helps prevent door from popping open mid-cycle
• Commonly used when the latch feels loose, the door won't stay closed, or cycles won't start
• Works with the appliance's existing latch assembly to return the latch to its resting position

• One spring for the door latch

• High-level replacement: remove access panel or door trim to reach the latch assembly
• Handle spring under tension carefully and wear eye protection to avoid injury
• If other latch components are damaged or worn, replace the entire latch assembly for a reliable repair
• Unplug the appliance or disconnect power before starting any repair

This door lock spin enable switch signals the washer's control that the door is securely locked so the cycle can advance into high-speed spin. Replacing a failed switch restores safe spin operation and prevents door/lock-related interruptions.

• Confirms the door latch is fully engaged and enables spin
• Prevents the drum from spinning when the door is not locked
• Common failure symptoms: won't spin or stops before high-speed spin; door/lock light doesn't come on; intermittent spin or door/lock error

• Disconnect power (and turn off water) before servicing
• Access the door latch assembly; remove the door boot clamp if required
• Transfer wires to the new switch one at a time; secure the switch in the latch housing
• Reassemble, verify the door locks, and run a spin test

The Dryer Light Bulb is an OEM part for Whirlpool dryers. This bulb is specifically designed to provide illumination inside the dryer drum, allowing for better visibility when loading and unloading laundry. It ensures a well-lit drying environment.

Causes of a bad dryer light bulb can include normal wear and tear, electrical issues, or accidental breakage.

Symptoms of a bad dryer light bulb may include:

• The bulb not turning on when the dryer door is open.
• Dim or flickering light inside the dryer drum.
• A burnt-out or broken bulb.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 6-32 machine screw fastens brackets, panels, and internal components in your appliance. Replacing a missing or stripped screw restores a secure, rattle-free fit and keeps assemblies properly aligned during normal operation.

• Secures components to frames, brackets, or covers
• Helps maintain proper alignment of panels and hardware
• Replaces missing, damaged, or stripped fasteners
• Common signs: loose/rattling panels, misaligned parts, or a screw that won't tighten

• Disconnect power (and water, if applicable) before servicing
• Match thread and length to the original fastener; reuse any washers if present
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the driver that matches the head style on your original screw

• Thread size: 6-32 (machine screw)

This sliding gear latch replaces the latch gear that secures the appliance door and helps engage the door lock mechanism for normal operation. It restores reliable door latching so cycles can start and run properly. What it does:

• Replaces the sliding gear used by the door latch assembly to engage/disengage the door lock
• Helps restore a door that won't stay closed or won't latch reliably
• Addresses symptoms like a door that won't lock, intermittent latch engagement, or door-related cycle start failures
• Works as a direct-fit internal latch gear when the original is worn or broken

• 1 sliding gear latch

• Unplug the appliance or disconnect power before beginning any repair
• Access may require removing the door panel or latch housing—keep fasteners organized for reassembly
• Install the part in the same orientation as the original; verify smooth movement of the latch mechanism before reassembling

This replacement axle/latch spring secures the latch/axle assembly so the appliance door or panel stays engaged during use. It restores proper latch tension for reliable closing and operation. What it does:

• Applies tension to the latch/axle so the door or access panel stays closed and latched
• Helps ensure the appliance detects a closed door and will start or run normally
• Common symptom: door won't stay closed or latch feels loose or fails to engage
• Small metal spring designed for a specific latch assembly — not a universal part

• Disconnect power to the appliance before starting any repair
• Access may require removing a panel, bezel, or door — use proper tools and keep fasteners organized
• Handle the spring and latch components carefully; springs are under tension and can snap free

The Wax Motor is an OEM part for Whirlpool washing machines. It is a crucial component responsible for driving the agitator or impeller that circulates and agitates the water and clothing during the wash cycle.

Symptoms of a faulty Wax Motor include:

• Washing machine not agitating or spinning during cycles
• Loud grinding or screeching noises from the motor area
• Burning smell or smoke from the motor overheating
• Error codes related to the motor or drive system

Causes of a bad Wax Motor can include mechanical failure due to wear and tear over time, electrical issues, or problems with the motor bearings or windings. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This hinge kit replaces a worn or damaged refrigerator/freezer door hinge to restore proper door alignment and sealing. It helps stop door sagging and ensures smooth opening and closing for a tight temperature seal. What it does:

• Replaces a damaged or bent door hinge to correct misaligned or sagging doors
• Restores smooth hinge movement for easier opening and closing
• Helps the door seal properly to maintain internal temperature and efficiency
• Prevents rubbing or binding that can damage door gasket or cabinet finish

• Disconnect power to the appliance before beginning any repairs to avoid injury
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use basic hand tools; follow for correct alignment and torque
• After installation, check door alignment and gasket contact; adjust as needed

This factory replacement hinge screw secures the door hinge to the appliance cabinet or door. Replacing a worn or missing screw restores solid door mounting and alignment for safe, reliable opening and closing.

• Fastens the hinge securely to the door or front panel
• Helps maintain proper door alignment to prevent rubbing or sagging
• Replaces missing, stripped, or corroded hardware
• Typical symptoms include a loose/sagging door, difficulty latching, or rattling at the hinge area

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Support the door while removing and installing hinge screws
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace them together for consistent alignment

This hinge cover is a small trim piece that conceals the door hinge and mounting screws. Replace a cracked or missing cover to restore a clean, finished look and help keep lint and debris out of the hinge cavity.

• Covers and protects the door hinge and screw heads
• Restores a smooth, finished appearance around the hinge opening
• Helps shield the hinge pocket from lint and debris
• Common replacement when the original cover is cracked, missing, or loose

• Disconnect power; for gas units, also shut off the gas supply
• Support the door; loosen/remove hinge screws as needed to access the cover
• Remove the damaged cover; position the new cover and secure per model design
• Verify door closes and aligns properly before returning to service