Parts for Maytag MLE2000AYW: 11 - Motor & Motor Control Parts

This is a Whirlpool washer drive motor and control board. The drive motor and motor control board are responsible for the spin cycles of the washer. A faulty motor may show signs of malfunction through a slower than average spin cycle. When the control board shorts out, the washer typically will not spin at all.Begin installation by removing the body of the washer. There are two screws at the base of the console. Remove these screws and flip the console back. Two clips are holding the body in place. Remove them with a flat-head screwdriver. Push these clips and pull the body off the washer. Now that the motor is exposed, remove the screws holding the motor in place with a nut driver. Two more clips fasten the motor. Push these clips with the flat head, and the motor is free to remove. Unplug the control board's wire harness from the washer. The new component is ready for install after these steps.The part is sourced directly from the manufacturer as a genuine OEM product. This kit is sold separately from the washer. This product is compatible with Whirlpool, Maytag, and Admiral appliances.

This is a Whirlpool washer drive motor and control board. The drive motor and motor control board are responsible for the spin cycles of the washer. A faulty motor may show signs of malfunction through a slower than average spin cycle. When the control board shorts out, the washer typically will not spin at all.Begin installation by removing the body of the washer. There are two screws at the base of the console. Remove these screws and flip the console back. Two clips are holding the body in place. Remove them with a flat-head screwdriver. Push these clips and pull the body off the washer. Now that the motor is exposed, remove the screws holding the motor in place with a nut driver. Two more clips fasten the motor. Push these clips with the flat head, and the motor is free to remove. Unplug the control board's wire harness from the washer. The new component is ready for install after these steps.The part is sourced directly from the manufacturer as a genuine OEM product. This kit is sold separately from the washer. This product is compatible with Whirlpool, Maytag, and Admiral appliances.

This motor control assembly operates the washer's drive motor to manage spin and agitation cycles, restoring proper motor response and cycle operation when the original control fails. What it does:

• Regulates motor speed and direction for agitate and spin functions
• Enables motor start/stop commands from the main control board
• Works as the replacement electronic module that sends power and control signals to the motor

• Disconnect power before replacing; follow all safety precautions to avoid shock
• Handle the board and connectors carefully to avoid ESD or connector damage
• Compare new part to the old unit for correct connector layout and mounting

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This is a Whirlpool washer drive motor and control board. The drive motor and motor control board are responsible for the spin cycles of the washer. A faulty motor may show signs of malfunction through a slower than average spin cycle. When the control board shorts out, the washer typically will not spin at all.Begin installation by removing the body of the washer. There are two screws at the base of the console. Remove these screws and flip the console back. Two clips are holding the body in place. Remove them with a flat-head screwdriver. Push these clips and pull the body off the washer. Now that the motor is exposed, remove the screws holding the motor in place with a nut driver. Two more clips fasten the motor. Push these clips with the flat head, and the motor is free to remove. Unplug the control board's wire harness from the washer. The new component is ready for install after these steps.The part is sourced directly from the manufacturer as a genuine OEM product. This kit is sold separately from the washer. This product is compatible with Whirlpool, Maytag, and Admiral appliances.

Specs: 10 - 16 x .375

Size: 10-24 x 3/8 inch.