Parts for Maytag MSD2456GEW: 02 - Controls Parts

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This temperature control thermostat regulates the refrigerator compartment temperature by cycling the cooling system on and off. Replacing a faulty control restores consistent cooling and normal on/off operation so food stays at the right temperature.

• Senses compartment temperature and opens/closes electrical contacts to start or stop cooling
• Useful when the fridge is too warm or too cold despite adjustments
• Common symptoms: runs constantly or won't run, temperatures don't respond to the dial, no click or change when turning the control
• Also called a "cold control"; restores functional temperature adjustment

• Disconnect power before servicing
• Note wire locations and transfer them to the new control
• Carefully route the sensing capillary in the original path; avoid kinking or sharp bends
• Set to a mid-range setting and allow up to 24 hours for temperatures to stabilize

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This is a replacement mounting screw for securing appliance components and panels. It restores proper fastening where a missing or stripped screw causes loose parts or rattling. What it does:

• Fastens panels, brackets, or small components to restore secure attachment
• Prevents vibration and rattling caused by loose or missing fasteners
• Replaces stripped or lost factory screws to maintain original fit
• Matches OEM fit for the specific mounting location when the part number is specified

• Use the matching screw location and size specified by the parts diagram
• Hand-start threads to avoid cross-threading; tighten securely but do not overtighten
• Disconnect power to the appliance before removing panels or components
• If threads are damaged, replace with correct OEM screw—do not force a mismatched fastener

The defrost timer controls your refrigerator's automatic defrost cycle, periodically pausing cooling to power the defrost heater. Replacing a faulty timer restores proper defrosting to help prevent frost buildup, temperature swings, and excessive run time.

• Advances the system between cooling and defrost at set intervals
• Sends power to the defrost heater, then returns the unit to cooling
• Failure may cause heavy frost on evaporator coils and weak airflow
• Fresh food section may run warm while the freezer ices over
• Unit may run constantly, never defrost, or get stuck in defrost

• Disconnect power before servicing
• Location varies by model; access the timer (often in the control housing or rear compartment), note wire positions, and transfer one at a time
• Mount and secure the timer as originally installed; reuse existing bracket/fasteners
• After reassembly, restore power and verify the unit advances through cooling and defrost

A replacement door gasket that restores a tight seal around the oven door to help maintain proper cooking temperature and improve efficiency. Fits Whirlpool ovens and ranges that use part A3189394. What it does

• Seals the oven cavity to reduce heat loss and help maintain consistent cooking temperatures.
• Helps prevent heat from escaping around the door, improving energy use and cook results.
• Worn, torn, or flattened gaskets can cause uneven baking or longer cook times.
• Replacing a damaged gasket can reduce hot spots on the exterior and nearby cabinetry.

• Disconnect power and ensure the oven is completely cool before starting.
• Remove the old gasket by pulling it out of the door channel; clean the channel before installing the new gasket.
• Press the new gasket into the channel around the full perimeter, working from one corner and ensuring an even fit.

The Whirlpool light bulb is an OEM replacement part responsible for providing illumination within the appliance, typically found in the interior of a refrigerator or oven. This incandescent bulb features a small screw-in base and clear glass. It operates at 120 volts and has a power rating of 25 watts. Its primary function is to emit light when the appliance's door or lid is opened, allowing users to see and access the contents inside.

Causes of a bad light bulb can include regular wear and tear from frequent use, electrical surges, or damage from handling. Over time, light bulbs naturally burn out and require replacement to maintain adequate lighting inside the refrigerator.

Symptoms of a bad light bulb include:

• The refrigerator or freezer compartment being dark when the door is opened
• Flickering or dim lighting
• A completely non-functional light bulb

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Door Switch is an OEM part for Whirlpool refrigerators. This switch is crucial for controlling the interior lights and the activation of certain refrigerator functions when the door is opened or closed. 

Symptoms of a failing Door Switch include:

• Interior lights staying on when the refrigerator door is closed
• Interior lights not turning on when the door is opened
• The refrigerator unexpectedly starting or stopping
• Alarms or indicators malfunctioning, signaling an open door when it is closed

Causes of a bad door switch can involve mechanical failure due to wear and tear from frequent use, damage from impacts (such as slamming the door), or electrical issues like a short circuit or faulty wiring.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Whirlpool EveryDrop Refrigerator Water Filter 7 features a coconut carbon filter that reduces contaminants to provide clean, fresh tasting water. This filter is used Whirlpool side-by-side refrigerators which accept Filter 7. Single filter. Simple, quick turn installation requires no special tools. For best performance, replace every six months. Certified to fit these leading refrigerator brands: Maytag and Jenn-Air. Micron Rating: 0.5. Filter Media: Coconut Carbon Block. Flow Rate: 0.5 GPM. Temp Range: 33 - 100 °F. Pressure Range: 30 - 120 psi. Meets NSF Standard: 42. Approved for WQA Gold Seal. Approximate dimensions: 8.25" x 8.25" x 6.5"

This refrigerator water filter bypass plug is used when you don't want to use a filter. Color: white. It measures about 3 inches in diameter.

This control wire harness routes power and control signals between the appliance control board and components, restoring reliable electrical connections for proper operation. Designed as a direct replacement when the original harness is damaged or faulty. What it does

• Carries power and low-voltage control signals from the main control to switches, sensors, and motors.
• Restores lost or intermittent function caused by frayed, burned, or broken wiring.
• Helps eliminate control errors and communication faults tied to damaged harness connections.
• Maintains correct routing and connector fit to prevent chafing and short circuits.

• One control wire harness as shown

• Always disconnect power (unplug or shut off breaker) before beginning work.
• Compare new harness to the old one to ensure matching connector types and lengths before installation.
• Label or photograph connector locations to ensure correct reattachment; route and secure harness away from heat and moving parts.

(SOLENOID NOT AVAILABLE MUST ORDER ICE DOOR KIT 12001991)