Parts for Electrolux FFRG1001PW0: 03 - Front Panel / Lint Filter Parts

This is a grille cover that sits over the lint screen opening on the top or front of the dryer. It protects the lint filter slot and provides a finished appearance while allowing proper airflow during the drying cycle. Replace this cover if it is cracked, broken, or missing, which can allow debris to bypass the lint filter and reduce drying efficiency.

White plastic plug insert that covers unused openings on your dryer. Keeps out dust and debris while restoring a clean finish. Replace if cracked or missing.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Wire harness assembly for dryers and laundry centers. Connects electrical components throughout the machine. Replace if wires are damaged or frayed.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

Traps lint and debris during drying. Replace when mesh appears clogged, melted, or reduces airflow. Confirm fit with your model number before ordering.

Secures hose connections in dryers to prevent leaks and maintain proper airflow. Replace if hoses are loose or disconnected. Verify fit with model.

Mounting screw secures panels, brackets, and internal components in your dryer. Replace if missing, stripped, or damaged during repairs or maintenance.

This replacement screw fastens panels, brackets, and internal components so assemblies stay aligned and tight during operation. With an 8-18 thread and 0.711-inch length, it matches the original hardware for a precise, reliable hold.

• Secures panels, brackets, and internal components to the cabinet/frame
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration, rattling, and gaps from loose hardware
• Restores proper alignment after service or transport

• Disconnect power and shut off water/gas before servicing.
• Support panels/components while removing and installing the screw.
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten.

This hardware component allows the dryer door to swing open and closed, typically mounted on the dryer frame and door. Replace it when the door sags, won't stay closed, or makes squeaking noises when opening.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

This outer refrigerator cabinet door replaces a damaged or dented door to restore the appliance's appearance and proper closure. It fits compatible Frigidaire refrigeration units and provides the exterior panel for the door assembly. What it does

• Replaces a dented, cracked, or cosmetically damaged outer door panel
• Restores proper closure alignment when the existing door is bent or warped
• Provides the mounting surface for handles, trims, and the door gasket
• Helps maintain internal temperature by allowing a proper door seal

• One outer refrigerator cabinet door (as shown)

• Remove power to the appliance before beginning work and follow all safety guidelines
• Installation typically requires removing the hinge assembly and lifting the door off the hinge pins
• May require transfer of handles, trims, and gasket from the old door; verify fasteners and hardware before installation
• If the door interfaces with water or ice components, shut off the water supply and take care when disconnecting plumbing

Replace a cracked, worn, or missing spacer in your dryer. This part helps maintain proper spacing between components during operation.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.