Parts for Maytag MDG16CSSAW: 09 - Tumbler (Mdg16cssaw) Parts

Color: white. It measures about 12-1/2 inches wide by 8 inches high.

The Tumbler Bearing Kit is an OEM replacement part for Whirlpool washing machines. It includes multiple replacement glides that support the movement of the wash basket or tub. As it rotates during the wash cycle, the tub experiences friction that the bearings help manage.  For rear drum support rollers, order 12001541. Please note that repair requires two kits.

Symptoms of bad bearings include:

• Excessive noise or vibrations emanating from the tub area
• Difficulty rotating or spinning the tub by hand  
• Visible wear on the bearings
• Premature breakdown of other components due to increased stress

Causes of bearing failure can be normal wear over time from the consistent rotational motion. Using the washer with an unbalanced load can accelerate bearing deterioration.

This OEM Whirlpool kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Specs: No.8X1/2 HEX WASHER HEAD

The Dryer Drum Felt Seal is an OEM part for Whirlpool dryers. It functions as a barrier, preventing hot air from escaping the dryer drum and ensuring that clothes are dried efficiently. This felt seal is located along the edges of the drum, creating a soft seal that also reduces noise and vibration during operation. For adhesive order WPY055980.

Causes of a bad dryer drum felt seal can include wear and tear over time, exposure to high temperatures that degrade the material, or physical damage from overloading the dryer.  

Symptoms of a bad Dryer Drum Felt Seal include:

• Clothes taking longer to dry or not drying completely
• Increased lint outside the lint filter area
• A noticeable gap between the dryer drum and the door
• Excessive noise or thumping sounds during operation

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: For Baffle mounting screws, order part# W11684512.

The Dryer Drum Baffle is an OEM part for Whirlpool electric dryers. Located inside the dryer drum, this rectangular component divides the airflow and improves drying efficiency. During cycles, the baffle helps separate clothes and direct heat more uniformly for even moisture removal throughout the load. This is the taller baffle. For the short one order WP33001755. 

Causes of a bad drum baffle can include constant impact from heavy loads, wear and tear over time, or damage from foreign objects in the drum.

Symptoms of a bad drum baffle include:

• Slow or prolonged drying times as air cannot circulate properly
• Some areas of clothes feeling damp while others are dry
• Lint or hair wrapping around a cracked or broken baffle
• Noise or vibration from a damaged baffle hitting the drum wall

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Note: For Baffle mounting screws, order part# W11684512.

The Dryer Drum Baffle is an OEM part for Whirlpool dryers. It is a component that helps direct and circulate the flow of heated air within the dryer drum, ensuring even and efficient drying of clothing. This part measures approximately 17 inches in length and 3-1/4 inches in height. Its mounting holes are positioned 12 inches apart, center to center. 

Causes of a faulty Dryer Drum Baffle include wear and tear over time, physical damage from foreign objects, or improper installation.

Symptoms of a bad Dryer Drum Baffle include:

• Clothes taking excessively long to dry or not drying evenly
• Excessive heat buildup or hot spots within the drum
• Loud rattling or thumping noises during the drying cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

This part is a replacement dryer tub. If the current dryer tub is broken or defective, this part can be used for replacement. It is intended for use with a variety of dryer models. The dryer tub is what holds clothes or materials that need to be dryer and rotates them in order to ensure they are dried sufficiently. Over time or with regular appliance use, this part may corrode, crack, dent, bend, or be otherwise damaged, requiring replacement. Ensure the appliance is entirely disconnected from the power source before attempting any repairs. It's recommended that work gloves are worn for protection.This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This dryer tub is suitable for use on a variety of dryer models manufactured by Whirlpool, Maytag, Crosley, and some other brands. It is sold individually.

The Dryer Drum Belt is an OEM replacement part for Whirlpool electric dryers. This belt rotates the tumbling drum to fluff and dry clothing loads efficiently. Continuous, uninterrupted drum movement is necessary for effective drying performance. This high-quality belt features 4 grooves and 5 ribs, with a width of 5/16" and a length of 91 5/8".

Causes of a faulty belt include breakage from age, cracks developing as rubber dries out, or slipping off the pulleys due to looseness or worn grooves.

Symptoms of a bad dryer belt include:

• Drum fails to turn or rotates slowly during cycles
• Loud squealing, screeching noises originating from inside  
• Smoky smells from belt slipping against fast-turning pulleys
• Possible jolts, jerks or prevented operation of dryer 

This belt is also compatible with KitchenAid, Maytag and Jenn-Air models too.

Size: #9-15 x 1 inch long. Hex head.

Specs: 10 - 16 x .375

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

This Hex Nut is a small but critical fastener used to secure brackets, panels, and internal assemblies in your appliance. Replacing a stripped, corroded, or missing nut restores a tight, rattle-free, and safe installation.

• Threads onto a matching bolt or stud to clamp parts together
• Helps maintain alignment and reduce vibration-related loosening
• Commonly used on panels, brackets, supports, and internal assemblies
• Replace when threads are damaged, hex flats are rounded, or hardware is missing
• Symptoms can include loose or rattling components or hardware that won't stay tight

• Disconnect power and, if applicable, shut off gas or water before servicing
• Use the correct-size nut driver or wrench to avoid rounding the hex
• Start the nut by hand to prevent cross-threading; tighten snugly without over-torquing
• Inspect and replace any damaged mating bolt/stud or washer for a secure repair

The Fiber Washer is an OEM part for Whirlpool appliances. This washer provides a reliable seal and is used in various connections within the appliance to prevent leaks and ensure secure fittings. Its fiber construction offers durability and resistance to wear, making it ideal for maintaining tight seals in high-pressure or high-temperature environments.

Common causes of a bad fiber washer include degradation from water or chemical exposure, physical damage from over-tightening, and natural wear and tear.

Symptoms of a bad fiber washer include:

• Water or fluid leaks at connection points
• Loose fittings or connections
• Visible wear, cracks, or deformation of the washer
• Decreased performance of the appliance due to improper sealing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Dryer Drum Roller Axle is an OEM part for Whirlpool dryers. It plays a role in the dryer's operation by offering support and an axis for the drum roller to spin smoothly. This guarantees effective and balanced tumbling of clothes throughout the drying cycle. 

Causes of a bad Dryer Drum Roller Axle can include prolonged use leading to wear and tear, accumulation of lint and debris causing additional friction, or improper loading of the dryer drum which can bend or strain the axle.

Symptoms of a bad Dryer Drum Roller Axle include:

• Unusual noises, such as squeaking or grinding, during the operation
• The dryer drum struggling to turn or not turning at all
• Increased vibration or shaking of the dryer unit
• Clothes taking longer to dry or not drying evenly

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Drum Support Roller is an OEM replacement part for Whirlpool dryers that is responsible for supporting the drum and allowing it to rotate smoothly. Causes of a bad Drum Support Roller can include lint and debris that accumulates and causes the rollers to malfunction or seize.

Causes of bad Drum Support Rollers can include wear and tear over time, excessive load imbalances, or physical damage from impact or mishandling.

Symptoms of a bad Drum Support Roller include:

• Unusual noises, such as thumping or squealing.
• The dryer drum struggling to rotate or not turning smoothly.
• Increased vibration or shaking of the dryer during operation.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Fiber Washer is an OEM part for Whirlpool appliances. This washer provides a reliable seal and is used in various connections within the appliance to prevent leaks and ensure secure fittings. Its fiber construction offers durability and resistance to wear, making it ideal for maintaining tight seals in high-pressure or high-temperature environments.

Common causes of a bad fiber washer include degradation from water or chemical exposure, physical damage from over-tightening, and natural wear and tear.

Symptoms of a bad fiber washer include:

• Water or fluid leaks at connection points
• Loose fittings or connections
• Visible wear, cracks, or deformation of the washer
• Decreased performance of the appliance due to improper sealing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Retaining Clip is an OEM part for Whirlpool stand mixers. This small but essential part ensures the stability and secure fitting of various mixer components, contributing significantly to the appliance's overall performance and durability. Its primary role is to hold parts in place, preventing movement that could lead to wear or malfunction during operation.

Stand mixers are subjected to a variety of stresses, particularly when mixing thick doughs or other dense mixtures. The retaining clip's integrity is vital in these situations, as it helps to maintain the correct alignment and functioning of the mixer's moving parts. 

Symptoms of a bad Retaining Clip in a stand mixer include:

• Components such as beaters or attachments becoming loose or detaching during use.
• Unusual vibration or noise 
• Difficulty in attaching or detaching mixer attachments  

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Screw: 8-16 x 3/8 inch.