Parts for Amana LE8317W2B / PLE8317W2 B: 12 - Rear Blkhd,Felt Seal, Roller & Term Blk Parts

This terminal block provides a secure connection point for the appliance's main power and incoming wiring, restoring reliable electrical contact and preventing loose or arcing connections. What it does:

• Creates a stable, screw-down connection for incoming power wires and internal leads
• Helps prevent intermittent power, arcing, or burning at the connection point
• Used where the power cord or internal harness attaches to the appliance chassis
• Commonly replaced when terminals are loose, melted, corroded, or show signs of overheating

What's included:

• One terminal block

Install notes:

• Disconnect power at the breaker or unplug the appliance before starting any work
• Take a photo of existing wiring before removal to ensure correct reconnection
• Reuse existing screws or replace with equivalent hardware; tighten firmly but avoid overtightening
• If terminals show heat damage or corrosion on mating connectors, replace both the block and affected connectors

Machine screw fastens panels, brackets, and components inside appliances. Replace stripped, missing, or loose screws to restore secure assembly.

Size: 10-24 x 3/8 inch.

Size: 10-24 x 3/8 inch.

10 - 16 x 1/2

Dryer drum roller axle mounts to the rear panel and supports drum rollers. Replace if bent, worn, or wobbling. Helps eliminate noise from damaged axles.

10 - 16 x 1/2

The Thrust Washer is an OEM part for Whirlpool washers and dryers, reduces friction between moving parts within the appliance. This small component is placed between rotating surfaces to ensure smooth operation and to extend the lifespan of those parts. The thrust washer can wear down or become damaged due to the constant pressure and movement.

Causes for replacement may include normal wear and tear, overloading the appliance, which puts extra stress on mechanical components, or a lack of regular maintenance.  

Symptoms of a bad Thrust Washer include:

• Increased noise during operation
• The appliance vibrating more than usual
• A decrease in performance efficiency

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Retaining Ring is an OEM replacement part for Whirlpool dryers and washing machines. This retaining ring holds the rear wheels on the axels of the washer or dryer. 

Symptoms of a bad retaining ring can include wear and tear over time, damage due to accident or impact, or corrosion affecting the structural integrity.

Causes of a bad retaining ring dryer include:

• Excessive vibration or movement of the drum during operation 
• Noise or banging sounds from loose components   
• Deformation or cracking of the retaining ring itself
• The dryer door not closing properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This roller supports and stabilizes the dryer drum as it rotates. Replace if worn, cracked, or causing noise during operation. Installs behind the drum.

Shaft that the idler pulley rotates on in your dryer. Replace if worn, wobbling, or causing squealing. Helps maintain proper belt tension and alignment.

This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.

• Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
• Helps prevent fasteners from loosening due to vibration and thermal cycling
• Common fix for rattling/vibration noises and components that work loose over time
• Replaces damaged, rounded, or missing original nut to restore proper fit

• Disconnect power and shut off gas/water supplies before servicing
• Remove the worn nut with the appropriate wrench or socket
• Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
• Inspect the mating bolt/stud and any washers; replace if worn or damaged

Replace your dryer's drum felt seal to stop air leaks, reduce noise, and prevent clothing stains. Fits between drum and bulkhead. Confirm fit with model.