Parts for Mtd 170-LU: Lu Carburetor Parts

M6 x 110mm carburetor mounting stud for small engines. Secures carburetor to engine block. Replace if stripped, corroded, or missing to ensure proper installation.

Fix rough idling and poor fuel mixture with a new carburetor insulator gasket. Prevents air leaks that affect engine performance. Simple DIY repair.

This carburetor insulator is a genuine MTD replacement part for appliances with small engines, such as lawn mowers, lawn tractors, lawn trimmers, snowblowers, chipper shredders, tillers, and leaf blowers. The function of a carburetor insulator in a small engine appliance is to maintain a lower temperature for a running engine and to keep that heat away from the carburetor, the purpose of which is to mix the air and fuel in order to start the engine. A functioning carburetor insulator will prevent the engine from overheating.A broken or non-functioning carburetor insulator will likely not prevent the engine from operating, but it might slow down its power or reduce its fuel economy due to compensation from overheating. An engine with a damaged carburetor insulator might take in more fuel than usual or allow in unmetered air. An unmetered air leak can cause damage to the engine in the short-term so if there appears to be visible damage to the carburetor insulator, it should be replaced as soon as possible.This carburetor insulator is compatible with the following brands: MTD, Cub Cadet, Yard Machines, and Craftsman.

Seals carburetor to insulator plate, preventing fuel leaks. Replace when worn, cracked, or torn to restore engine efficiency. Verify fit with your model.

Genuine carburetor assembly for lawn and garden engines. Creates proper fuel-air mixture for combustion. Replace if cracked, leaking, or damaged.

Seals between carburetor and engine block to prevent air and fuel leaks. Replace if engine runs rough, leaks gas, or loses power. Verify fit by model.

This carburetor rebuild kit is designed for use in a variety of lawn and garden engines. It contains the necessary components to rebuild the carburetor when it is not working. The air to fuel ratio is controlled by the carburetor. This mixture goes to the cylinder to ignite the engine. When the carburetor is not working properly, the ratio is not correct, and the engine does not run smoothly. If the carburetor is the suspected point of failure on the machine, test it by removing the air filter and pouring a small amount of gas directly into the carburetor. If the engine fires up but then dies, the carburetor needs to be repaired or replaced. Rebuilding the carburetor is less expensive than replacing it and can be done in a short time. Always work in an area with adequate ventilation. Remove the fuel and spark plug from the machine before starting. Remove the carburetor and replace the gaskets using the rebuild kit. Reinstall the carburetor and all the parts removed while working on the machine. This carburetor rebuild kit is sold as an individual part. It is compatible with log splitters and other small engines manufactured by MTD and Troy-Bilt.

This plastic body fuel shutoff lever is a genuine OEM replacement part for many different engines on lawn and garden equipment. It is part of the fuel shutoff valve assembly. This valve controls the gas flow from the fuel tank to the engine. The shutoff lever is used to open or close the valve. This lever is a plastic part that may break or crack over time. Exposure to rain and snow and excessive use may lead to damage. When this happens, the shutoff lever should be replaced to prevent fuel from leaking from the fuel tank.Repairs to the fuel tank should be made outside where there is adequate ventilation. Remove all fuel from the fuel tank and take the spark plug out before working on the shut off lever. Remove the fuel tank from the machine and turn it upside down to get to the fuel shutoff lever. Remove the lever from the shutoff valve. Install the new shut off lever. Reinstall the fuel tank and fill it with fuel.This fuel shutoff lever is sold individually. It is made for MTD and Troy-Bilt log splitters and other small engines.

Fix fuel leaks or loose carburetor connections with this fuel bowl mounting bolt. Secures the fuel bowl to prevent sediment clogs. Quick 5-minute fix.

It's best to have spare O-ring gaskets on hand to rebuild a carburetor when the need arises. Use this manufacturer-approved replacement part to complete the process. When outdoor power equipment shuts off just after starting or won't start altogether, there may be a problem with the carburetor. It could be a leak that causes compression problems keeping the machine's engine from starting. Gasoline may drip from the float bowl because of an O-ring that won't seal or seat evenly all around, or one that has become brittle over time. This is a genuine OEM part compatible with specific lawnmowers, snowblowers, wood chippers, log splitters, tillers, and other garden maintenance machines from Craftsman, MTD, Cub Cadet, MasterCut, Troy-Bilt, and Yard Machines. It is sold individually.

This choke control lever automatically regulates the combined amount of air and fuel that come together in a small gasoline powered engine's carburetor to give a cold engine a fuel-rich mixture when the motor is first started. The control lever has several positions that allow it to adjust the fuel/air mixture in lawn equipment such as lawn mowers, snow blowers, tillers, chippers, log splitters, and other small gas engines. Over time with regular use, the control lever may become worn and must be replaced. There are several signs that indicate a choke control lever may be failing. If the gas tank is full of fresh gasoline but the engine refuses to start, if the engine starts and quickly floods, or if the engine runs at top speed but does not idle, the choke control level may be need to be replaced. Should the choke control lever need to be replaced, it is essential to use an OEM genuine manufactured replacement part such as this one. OEM parts are built to the exact specifications of the equipment's original parts. This part is compatible with Huskee, Cub Cadet, Yard Man, MTD, Yard Machines, and Troy-Bilt brand equipment.

Creates a leak-proof seal between the fuel drain plug and tank. Replace if you notice fuel leaking from the drain area. Verify fit with your model number.

Seals the fuel bowl to prevent leaks and keep dirt out of your fuel system. Replace when cracked or leaking. Confirm fit with your model number.