Admiral Dryer Parts

Seals unused factory or service holes on your dryer cabinet or liner. Restores a clean appearance and keeps dust out. Replace if cracked, broken, or missing.

This bulkhead is the front tub housing that supports the washer drum and seals the washer cabinet to help contain water. Replaces a cracked or corroded housing to restore proper drum alignment and help prevent leaks. What it does:

• Provides structural support for the washer tub and drum assembly
• Forms the front seal surface to help keep water inside the washer
• Helps maintain correct drum alignment to reduce noise and wobble
• A failing bulkhead can cause visible leaks, excessive vibration, or rubbing noises

• Disconnect power and water supply before starting any repair
• Inspect surrounding seals, gaskets, and mounting hardware when replacing the bulkhead
• Replacement may require partial disassembly of the washer cabinet and drum; follow OEM instructions

Adjustable leveling leg with foot pad for dryers, washers, and pedestals. Replace cracked, broken, or missing legs to stabilize your appliance.

This knob assembly replaces the "modifier" control knob on the console so you can adjust settings smoothly and reliably again. Restore a secure, positive-turn feel when the original knob is cracked, stripped, or missing.

• Attaches to the control shaft to select and adjust options/settings
• Replaces knobs that are cracked, broken, or missing
• Fixes a knob that spins freely, slips, or won't turn the control
• Restores proper selection and tactile feedback during use

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel
• Align the flat/splines on the new knob with the shaft and press on firmly until fully seated
• The pointer aligns with the panel markings before use

Replace your cracked, stripped, or missing selector knob. Attaches to the control shaft to choose wash cycles and options. Restores smooth operation.

This rotary on/off switch controls the dryer's Finish Guard (also called Wrinkle Guard/Wrinkle Shield) feature. Replacing it restores proper control of the post-cycle intermittent tumbling that helps reduce wrinkles, preventing the feature from being stuck on or off.

• Provides 2-position on/off selection for the Finish Guard/Wrinkle Guard function
• Failure can cause the feature not to engage or to stay on after the cycle ends
• Knob may feel loose or fail to click when the switch is worn
• Mounts in the control console and interfaces with the external selector knob

• Disconnect power before servicing
• Access through the control console; remove paneling as needed
• Transfer wires one at a time or photograph connections for reference
• Reinstall using the existing knob and mounting hardware

This conversion kit includes the orifices and components needed to convert a natural gas dryer to operate on liquid propane (LP) gas. It ensures the correct fuel-to-air mixture for safe and efficient burner operation on LP. Use this kit when installing a natural gas dryer in a home that only has an LP gas supply.

Size: 26 inches long. F18t8/cw/k26.

Size: 10-24 x 3/8 inch.

Replace your dryer's damaged, dented, or cracked outer door panel. This finished surface panel installs on the front door assembly to restore appearance.

Dryer not heating properly or overheating? This cycling thermostat regulates temperature by cycling the heating element on and off. Moderate DIY repair.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.

This assembly includes the roller shaft and rear support bracket that holds a drum support roller in place inside the dryer. It allows the drum to rotate smoothly on its rear support rollers. Replace this part if the dryer is making squealing, thumping, or rumbling noises, or if the existing shaft is worn, bent, or seized.

This replacement door handle restores a secure, easy-to-grip surface for opening and closing the appliance door and refreshes the door's appearance. Designed to match factory fit and function when the original handle is cracked, loose, or missing. What it does:

• Provides a firm, ergonomic grip for opening and closing the appliance door.
• Restores proper mounting and alignment if the original handle is damaged or wobbly.
• Helps prevent injury from sharp or broken handle edges.
• Improves the appearance of the appliance door when the original is faded, cracked, or missing.

• One replacement door handle

• Before starting, disconnect power to the appliance or unplug it to reduce shock risk.
• Remove any trim or access panels per the service instructions to access handle fasteners.
• Keep original screws and small parts; use the OEM diagram to confirm orientation and placement.
• Do not overtighten fasteners—snug only to avoid cracking the handle.

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.