Admiral Refrigerator Parts

Size: 1/4 inch. Nut for plastic water line.

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

This replacement ice bucket housing encloses and supports the freezer's ice storage bin at the dispenser. A damaged housing can cause bin wobble or misalignment—replacing it restores a secure fit, smoother dispensing, and helps reduce stray ice and frost.

• Holds and aligns the ice bin for proper engagement with the dispenser mechanism
• Guides ice toward the chute and helps contain cubes and shavings
• Helps limit warm-air leaks around the bin to reduce frost and clumping
• Typical symptoms: bin won't seat or is wobbly, poor or no ice dispensing, ice spilling inside freezer, visible cracks in the enclosure

• Unplug the refrigerator and shut off water before servicing
• Remove the ice bin; take out any screws or clips securing the housing
• Transfer any reusable brackets or screws from the old housing to the new one
• Reinstall the housing level and secure; seat the bin fully, restore power, and test dispensing

Ice maker water line: 1/4x 8ft.

This base grille installs at the bottom front of the appliance to cover the lower opening and direct airflow through the ventilation area. Replace it to restore a clean, finished look when the original is damaged, loose, or missing.

• Finishes and protects the lower front of the cabinet
• Allows proper airflow through the front vent area
• Helps shield internal components from debris
• Replace if cracked, warped, broken tabs, rattling, or missing

• Disconnect power before servicing
• Remove the old grille by pulling outward at the top and lifting up, or by removing screws/clips if your model uses them
• Align tabs with slots and snap firmly into place
• Verify door clearance and secure fit, then restore power

This damper cover insert fits the refrigerator's air damper/diffuser. It helps guide and seal airflow from the freezer to the fresh food section, supporting stable temperatures and reducing drafts when the original insert is cracked or missing.

• Seats inside the damper cover to shape and restrict airflow between freezer and refrigerator compartments
• Helps seal the vent opening to limit air leaks
• Supports proper temperature balance and airflow distribution in the fresh food section
• Typical symptoms include a broken/missing insert, air drafts at the vent, rattling from the cover, or inconsistent cooling

• Disconnect power to the refrigerator before servicing
• Remove shelves as needed and access the damper cover in the fresh food compartment
• Release and remove the damaged insert; snap the new insert into the cover with correct orientation and a secure fit
• Handle nearby foam seals and the damper door carefully to avoid damage

This evaporator defrost heater melts frost from the evaporator coil during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice buildup that restricts cooling and leads to warm spots. What it does:

• Heats the evaporator coil to clear frost/ice during defrost
• Helps maintain proper airflow between freezer and fresh food sections
• Typical symptoms: heavy frost on the back panel/evaporator, weak cooling or rising temperatures
• Also cause evaporator fan noise from ice contact and longer run times

• 1 evaporator defrost heater

• Disconnect power before servicing; allow any ice to thaw
• Access the heater behind the freezer's rear panel; avoid damaging fins or refrigerant lines
• Secure the heater and route wires exactly as original, keeping them clear of the fan and sharp edges
• Restore power and verify the defrost cycle per the service procedure

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

This refrigerator door closer restores smooth, positive door action. When worn, the door can click, bind, or swing open. Replacing it helps the door seal properly to maintain temperatures and limit frost or moisture.

• Provides cam action at the bottom hinge for smooth opening and a positive close
• Helps pull the door shut during the last inches of travel to maintain gasket contact
• Typical wear symptoms: popping/clicking at the lower hinge, door that won't stay closed, or poor sealing
• Visual clues include flat spots, grooves, or cracks on the cam surface

• Disconnect power and remove items from the door for safety and to reduce weight
• Lift the door off the bottom hinge; transfer/install the closer in the same orientation as the original
• Reassemble, then verify the door self-closes and the gasket seals evenly
• Use care not to pinch or distort the door gasket during reinstallation

This defrost thermostat is a bi-metal switch that senses evaporator temperature during defrost and opens to stop heater power once the coil warms. Replacing a failed thermostat restores proper defrost, reducing ice buildup and airflow-related cooling problems.

• Monitors evaporator coil temperature during defrost
• Opens the heater circuit at a set temperature; recloses when cold for the next defrost
• Helps protect against overheating and ensures consistent defrost operation
• Common symptoms: heavy frost on the evaporator, weak airflow/warm fresh food section, repeated ice buildup after manual defrost

• Disconnect power before servicing; wear cut-resistant gloves
• Access the thermostat at the evaporator behind the freezer's rear panel
• Move wires one-for-one from the old part; mount in firm contact with the coil/tubing and secure leads away from the fan
• After installation, the thermostat should show continuity when cold and open circuit when warm

This is a replacement power cord that supplies electrical power from a wall outlet to your appliance. A fresh cord helps ensure safe, reliable power delivery when the original is damaged, overheated, or worn.

• Delivers household power to the unit's main electrical connection
• Replace if the cord is cut, cracked, burnt, loose, or intermittently powers the appliance
• Helps resolve issues like no power, tripping breakers, or visible cord damage

• Unplug the appliance and turn off the circuit breaker before starting
• Verify outlet type and cord routing match your original installation
• Transfer any cord clamp/retainer as needed and secure against sharp edges
• Inspect for proper grounding and test operation before returning to service

This black refrigerator toe grille covers the lower front opening, protecting internal components and helping guide airflow through the condenser while giving the appliance a clean, finished look. Replace a cracked or missing grille to restore fit and appearance.

• Helps direct airflow to the condenser area for proper ventilation
• Shields the machine compartment from bumps and debris
• Provides a finished, uniform look along the base
• Replace if cracked, warped, tabs are broken, won't stay attached, or rattles

• Disconnect power before servicing and wear cut-resistant gloves
• Remove the existing grille by releasing clips or removing screws (as designed)
• Align the new grille with mounting points and secure with the original fasteners
• Ensure ventilation slots are clear and unobstructed after installation

This ice enclosure is the molded housing for the refrigerator's ice compartment. It supports and protects the ice dispensing components and guides ice into the chute or bin, helping maintain proper alignment and smooth dispensing. What it does:

• Provides structural support for the ice bucket/auger and related dispenser components
• Helps guide ice from the compartment into the chute/bin to reduce spills and jams
• Aids in maintaining alignment and a consistent cold zone around the ice area
• Typical symptoms of failure: cracked/broken housing, ice bin won't seat securely, ice jams or intermittent dispensing, frost/ice buildup in the ice compartment

• One ice enclosure

• Disconnect power; remove the ice bin before service
• Note screw locations; detach the old enclosure and any connected clips or wiring
• Transfer any brackets or hardware from the original enclosure; reuse existing fasteners
• Mount the new enclosure without overtightening; restore power and verify normal dispensing

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

Restore a solid, comfortable grip on your freezer door with this black Freezer Door Handle. It replaces a damaged or worn handle to bring back dependable daily use and a clean, factory look.

• Provides a sturdy handhold for opening and closing the freezer door
• Direct replacement for a cracked, broken, loose, or missing handle
• Refreshes the appliance's appearance if the old handle is scuffed or discolored
• Installs on the existing mounting points for your model

• Unplug the appliance and secure the door before service.
• Access and loosen the handle's set screws or mounting screws, then remove the old handle.
• Position the new handle; transfer and tighten existing fasteners evenly—do not overtighten.
• Verify smooth door operation and alignment after installation.

This freezer door gasket replaces a worn or deformed seal to restore a tight, even closure on the freezer door. A proper seal keeps cold air in and humid air out, reducing frost buildup and temperature swings.

• Creates an air-tight seal between the freezer door and cabinet to contain cold air
• Helps maintain correct temperature and efficiency; reduces frost/ice around the door perimeter
• Symptoms of failure: tears, cracks, warping, gaps, or door not closing fully
• Presents as frost buildup, moisture/condensation, or warm spots in the freezer

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax (lay flat; warm gently with hot water or a hair dryer) for easier fit
• Remove the old gasket from the retainer/channel; on screw-retained styles, loosen (do not remove) liner screws as needed
• Seat the new gasket evenly, starting at the corners; use gentle heat to smooth wrinkles and ensure a uniform seal all around