Amana Dishwasher Parts

The Seal is an OEM part for Whirlpool dishwashers. As a crucial door component, it ensures a tight fit that prevents leaks and contains the necessary heat and moisture during operation. 

Symptoms of a bad seal can include cracks, tears, or looseness allowing water to escape during cycles. Deterioration from chemical exposure or repeated flexing over time is common.

Causes of a bad seal include general wear and tear, damage from improper loading of dishes, or accidents like sharp objects puncturing the material.

Symptoms of a bad seal include: 

• Puddles or pools of water found beneath the dishwasher after cycles
• Wet floors and surfaces surrounding the dishwasher  
• Steam or moisture visible escaping during heating phases
• The door not closing or latching properly

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Tank is an OEM part for Whirlpool washing machines. It properly dispenses detergent during the wash cycle.

Causes of a bad detergent tank can include: cracks, holes or other damage that cause leakage or improper detergent dispensing. Scaling or mineral buildup inside the tank over time may also lead to detergent dispensing issues.

Symptoms of a bad detergent tank include:

• Detergent not being fully dispensed or released during the wash
• Residue or leftover detergent remaining in the tank after cycles
• Clothes not getting properly cleaned due to insufficient detergent release

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dishwasher Door Seal is an OEM replacement part for Whirlpool dishwashers. It provides a tight seal around the dishwasher door to prevent water, sound, and heat from escaping during the wash cycle. Measuring 71” in length (and stretching up to 75”), this door seal prevents water from leaking out during wash cycles.

Causes of a bad seal can include cracks, tears, or splits that develop due to regular use and age. Damage may also occur from over-tightening of the door or accidental impact.

Symptoms of a bad dishwasher door seal include:

• Water or moist air leaks around the door during a cycle  
• Higher energy bills due to hot air escaping
• Excess moisture or mineral deposits around the door seal area
• Food particles or debris trapped under a torn seal

This genuine OEM Whirlpool replacement seal is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The OEM Electronic Control Board is an OEM replacement part for Whirlpool dishwashers. It is a circuit board that controls all of the functions of the dishwasher, including the wash cycles, water temperature, and detergent dispensing.

Causes of failure involve damage from liquid intrusion shortening circuits or component deterioration over extended use reducing precision.

Symptoms include:

• Dishwasher fails to start selected cycle
• Lights, displays or programming malfunctions
• No response from control buttons
• Dishwasher appears dead or powerless

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Volute with Seal is an OEM part for Whirlpool dishwashers. This part directs water flow within the dishwasher's pump, ensuring efficient circulation and pressure during the wash cycle. The seal helps to prevent leaks by maintaining a tight closure between the volute and other pump components.

Common causes of a bad volute with seal include wear and tear from regular use, damage from debris or hard water deposits, and seal degradation due to age or chemical exposure.

Symptoms of a bad Volute with Seal include:

• Water leaking from the pump area
• Decreased washing performance
• Unusual noises from the pump during operation
• Visible cracks or damage to the volute or seal

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

Replacement pump gasket with silicone sealing material that restores a watertight seal between the pump and housing. Helps stop leaks at the pump area and prevents water pooling under the appliance.

• Seals the pump to the housing to help prevent water leaks and drips.
• Common repair for visible water under the appliance or leaks coming from the pump area.
• Silicone sealing material provides a flexible, water-tight interface that conforms to the pump housing.
• Designed to replace the factory pump gasket for a direct fit and proper sealing.

• Disconnect power and water supply before beginning any repair.
• Remove the pump assembly to access and replace the gasket.
• Clean and dry mating surfaces before installing the new gasket; seat evenly to ensure a full seal.

Includes 2 white tines, 2 blue clips, and 1 white clip. The parts in this kit range from about 4 to 10 inches.

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

This spring provides the tension or return force used in the appliance's moving assemblies to restore position and maintain secure connections. It's a simple replacement that helps restore proper function and reduce slippage or sag. What it does:

• Replaces a worn or broken tension coil that provides return force for door, latch, or linkage components.
• Helps stop doors, latches, or moving parts from staying loose, drooping, or failing to return.
• Can reduce rattling or clunking caused by a failed spring under load.
• Often used where a compact coil spring is required to maintain tension in a mechanism.

• One replacement spring.

• Disconnect power (and gas if applicable) before servicing—always follow the appliance's safety instructions.
• Use proper tools and keep hands/loose clothing clear of pinch points; springs can release stored energy.
• Verify the exact spring orientation and attachment points before removing the old part.

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

This timer knob replaces a worn or broken control knob and restores a clear, easy-to-grip timer control. The biscuit finish matches neutral appliance trims for a clean, factory look. What it does:

• Fits over the appliance timer shaft so you can set cook/dry cycles or timer functions
• Provides a tactile grip and clear pointer for accurate timer selection
• Replaces faded, cracked, or stripped knobs that no longer turn or stay engaged
• Matches biscuit-colored control panels for a seamless appearance

• One timer knob (biscuit)

• Remove power to the appliance before servicing to avoid injury
• Pull the old knob straight off the timer shaft; align the new knob's splines and press on until seated
• No wiring or tools typically required, but for model-specific instructions

A stainless pushnut used to secure shafts, studs, or small components with a quick, push-on retainer that resists corrosion. Keeps parts fastened without threading or additional hardware for a clean, low-profile fit. What it does:

• Acts as a push-on retaining nut to hold shafts, studs, or fittings in place
• Provides a corrosion-resistant stainless finish for wet or high-humidity areas
• Prevents components from sliding off axles or posts during normal operation
• Commonly used on control shafts, knobs, or small internal assemblies

• Turn power off and unplug appliance before servicing to avoid shock or injury
• Push onto the post or shaft until fully seated; a firm press or light tap may be required
• Use appropriate hand tools or pliers with protection to avoid damaging the part
• Replace with identical part number to ensure fit and function

Color: Dark Gray

This snap-in outlet connector secures wiring to an appliance control or harness and restores a reliable electrical contact. Designed for a direct, tool-assisted snap fit, it helps eliminate loose or intermittent connections. What it does:

• Provides a secure snap-in electrical connection between wiring and the appliance harness or control
• Restores power flow when a worn or damaged outlet causes intermittent operation or no power
• Prevents arcing and poor contact that can result from loose terminals
• Matches OEM fit for straightforward replacement when the original snap outlet is broken or missing

• Disconnect power to the appliance before inspecting or replacing electrical parts
• Remove access panels as required to reach the outlet; replacement typically snaps into place
• Verify correct orientation and full seating of the connector to ensure a solid contact
• If corrosion or wiring damage is present, replace or repair wiring per OEM guidance