Amana Dishwasher Parts

Color: light gray. Measures about a 1/2 inch high by 4 inches deep.

The electronic control board is the appliance's main control module. It interprets inputs from the user interface and sensors, then powers and times key components to run each cycle. Replacing a failed board restores reliable, predictable operation.

• Coordinates cycle sequencing and powers components through onboard relays
• Receives signals from switches/sensors and manages overall operation
• Common failure symptoms: unresponsive controls or no power
• Won't start, stops mid-cycle, or won't advance through a cycle
• Intermittent operation, flashing lights, or fault/error codes tied to the main control

• Disconnect power at the breaker before servicing; verify the unit is de-energized
• Use ESD protection; handle the board by the edges to avoid static damage
• Photograph/label wiring and move connectors one at a time to the matching terminals
• After installation, run the appliance's diagnostic/test cycle to confirm proper operation

Color: White

This replacement door handle restores a secure grip and normal door operation on compatible Whirlpool appliances. It provides a like-for-like fit and finish to replace a damaged, loose, or worn handle so doors open and close reliably. What it does:

• Replaces a broken, cracked, or missing door handle to restore normal use
• Provides a solid grip so the door opens and closes smoothly
• Matches the original mounting points for straightforward fit
• Helps eliminate rattling or loose-handle symptoms

• One replacement handle

• Intended to be installed with the original mounting screws and hardware; only included items ship
• Turn off and unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use moderate force when aligning the handle to avoid damaging trim or fasteners

This coupler gasket creates a tight, leak-resistant seal at a coupler connection point, helping maintain proper operation of the assembly. Replace when the original gasket is worn, cracked, or flattened to prevent drips and seepage.

• Forms the seal between a coupler and its mating component
• Helps prevent water seepage and air intrusion at the joint
• Supports correct flow/pressure through the connection
• Common symptoms: drips at the fitting, moisture around the coupler, or needing to over-tighten to stop leaks

• Disconnect power and shut off water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; seat the gasket squarely in the coupler recess
• Tighten fittings evenly; restore service and check for leaks

The Impeller is an OEM part for Whirlpool brand dishwashers. Located within the dishwasher sump assembly, this plastic component utilizes rotating blades to circulate wash water throughout cycles.

Causes of a bad impeller can include cracking or damage from minerals over time, chunks of food debris jamming the blades, or normal wear on plastic.

Symptoms of a faulty impeller include: 

• Inadequate water circulation yielding poor cleaning 
• Food particles or utensils not fully rinsed
• Loud clicking or grinding noises mid-cycle
• Error codes relating to low water pressure

Replacing the impeller restores optimum water flow for Whirlpool dishwashers. Proper circulation using the OEM replacement ensures all portions of dishes and cycles receive sufficient water volume. Compatibility also includes Maytag, Jenn-Air, Amana, Magic Chef, and other brands.

This electronic control board is the appliance's central command module, directing power and timing so functions run correctly. Replacing a failed board helps restore normal operation when the unit is unresponsive or behaves erratically.

• Manages power and timing to components based on selected settings
• Interprets inputs from sensors/switches to control each step of the cycle
• Common symptoms: won't power on or start, unresponsive controls, random stopping, error codes/alarms

• Disconnect power before service; use ESD protection and handle the board by its edges
• Photograph wire/harness connections and transfer connectors one at a time
• Inspect and correct any shorted components or damaged wiring before powering up the new board
• After installation, follow the unit's tech sheet for any required tests, calibration, or programming steps

This top spray arm, also called the top wash spinner, restores proper water distribution to the top of the tub. It helps deliver even spray coverage so glasses and dishes on the upper rack come out clean. What it does:

• Rotates under water pressure to spray jets across the upper rack area
• Improves wash coverage and rinsing for items on the top level
• Common failure signs: poor cleaning on the top rack, arm not spinning, clogged jets, or visible cracks/warping
• May also cause uneven spray patterns or debris buildup if the spinner is damaged

• 1 top spray arm

• Disconnect power at the breaker and turn off the water supply before servicing
• Open the door; remove the upper rack if needed for access
• Release the retainer or screw, remove the old spinner, and clear any debris from the hub/feed area
• Install the new spinner and ensure it spins freely before running a test cycle

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This dispenser assembly replaces a refrigerator's door-mounted ice and water dispenser to restore normal dispensing and reduce leaks or delivery issues. It provides the core housing and user-facing dispenser opening for door-based dispensing systems. What it does:

• Directs water and ice from the door dispenser to the user, forming the visible dispensing opening and housing.
• Helps stop common dispenser symptoms such as water dripping from the dispenser opening or ice/jam buildup at the dispenser chute.
• Supports normal push-lever or paddle operation and routes water/ice to the exterior dispense area.

• Disconnect power and shut off the water supply before starting any work.
• Removal typically requires taking off the refrigerator door panel or trim to access mounting fasteners—retain all hardware and note fastener locations.
• Handle the dispenser housing carefully to avoid cracking plastic or damaging seals; inspect gaskets and fittings and replace if brittle.

This dishwasher impeller assembly mounts on the circulation pump and pressurizes wash water for the spray arms. Replacing a worn or damaged impeller restores proper spray pressure, cleaning performance, and quieter operation.

• Spins with the circulation motor to pressurize wash water
• Drives flow to the spray arms for effective wash action
• Typical symptoms: weak or no spray, poor cleaning results, grinding or rattling from pump area
• Often fails from broken vanes or debris; inspect filters/chopper while open

• Disconnect power and water before servicing
• Access is typically from inside the tub: remove the lower spray arm, filter screens, and cover to reach the impeller
• Note the order of parts and transfer any reusable hardware; replace worn O-rings/seals as needed
• Do not overtighten plastic parts; verify the impeller spins freely before reassembly and testing

Attaches to the inner tub for the upper rack

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

Pump housing only. For a complete pump and motor assembly, order WPW10247394.

This water inlet hanger secures the appliance's fill tube or line in the correct position, supporting a proper fill path and reducing strain on fittings. Replace a cracked or missing hanger to prevent movement, vibration, and potential leaks.

• Supports and positions the water inlet tube/line or inlet assembly
• Helps maintain alignment and sealing at the connection point
• Reduces vibration and prevents rubbing/chafing against surrounding parts
• Common symptoms include a loose or sagging inlet, rattling noises, chafed tubing, or drips from a misaligned inlet

• Disconnect power and shut off the water supply before servicing
• Access the inlet area and note the original hanger orientation and routing
• Remove the damaged hanger and mount the new hanger using the existing mounting points/fasteners
• Ensure the tube/line is secure and not kinked; restore service and run a brief test to check for leaks