Amana Dishwasher Parts

This float controls your dishwasher's water level. As the tub fills, it rises to signal the float switch to shut off incoming water, helping prevent overfilling and leaks.

• Lifts with the water to actuate the float switch and stop filling
• Helps protect against overfilling and door leaks
• Replace if the float is cracked, deformed, waterlogged, or sticks in its well
• Symptoms can include: won't fill or stops filling early; overfilling or leaks at the door

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the float in the tub floor
• Lift the old float straight up; clear any debris; seat the new float and free up-and-down movement
• Restore power and run a fill test to proper operation and check for leaks

This heater warms the wash water inside the tub during selected cycles. Replacing a failed element restores proper water temperatures, supporting cleaning performance and preventing extended run times or incomplete cycles. What it does:

• Heats water in the washer tub during hot/sanitize/temperature-controlled cycles
• Helps maintain target temperature for effective cleaning and stain removal
• Common symptoms include water not heating, cycles taking unusually long, or cycles stopping early
• Accompany control errors related to water temperature or the heater circuit

• 1 heater

• Disconnect power and shut off water supplies before servicing
• Access is typically from the rear or bottom; be prepared for residual water when removing the old element
• Clean sealing surfaces and seat the element fully; tighten fasteners evenly to prevent leaks
• After installation, run a hot cycle to check for leaks and heating

This cap secures the dishwasher wash arm to its support, helping keep the arm properly positioned so water jets can spin and spray effectively for consistent cleaning performance.

• Holds the wash arm in place on its hub/support
• Can help address a loose, wobbly, or detached wash arm
• Replacing a damaged or missing cap can restore stable arm rotation

• Disconnect power and turn off water before service
• Remove the lower rack for access; lift off the wash arm
• Unscrew/press off the old cap; seat and secure the new cap
• Ensure the wash arm spins freely by hand before reassembly

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

The Manifold is an OEM part for Whirlpool dishwashers. It is responsible for providing water supply to the spray arms during the wash and rinse cycles. It provides proper distribution of water throughout the dishwasher, allowing for thorough cleaning of your dishes. It connects the main water supply line to various parts within the dishwasher, ensuring a consistent flow of water.

A bad manifold can occur due to wear and tear, clogs, or damage to the tubing. If you notice symptoms such as reduced water flow, leaks, or improper cleaning results, it may be time to replace the water supply tube manifold.

Symptoms of a bad manifold include:

• Reduced water flow during the wash cycle
• Leaks or drips from the manifold area
• Improper cleaning or rinsing results

Repair your dishwasher by replacing the faulty or worn-out water supply tube manifold with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This thermal fuse protects your appliance by opening the circuit if temperatures climb beyond a safe limit, helping prevent wiring or control damage. When it blows, the unit may lose all power or stop mid-cycle. What it does:

• Cuts power when overheating is detected to protect internal components
• Helps prevent damage from shorted heaters, motors, or wiring faults
• Common symptoms: no power, won't start, shuts off during operation, no lights/display
• A blown fuse reads open (no continuity) and must be replaced—it is not resettable

• 1 thermal fuse

• Disconnect power before servicing to avoid electrical shock
• Access the fuse location per your model's service information; note wire orientation and mounting
• Replace one-for-one; do not bypass or up-rate the fuse. Identify and correct the overheating cause before restoring power.

This wax motor is the actuator for the dishwasher's rinse aid dispenser, releasing rinse agent at the correct time in the cycle. Replacing a weak or failed unit restores consistent rinse aid dispensing and helps minimize spotting.

• Actuates the rinse aid dispenser by extending a plunger when energized
• Works with the control to meter rinse aid during the final rinse
• Failure symptoms can include rinse aid not dispensing, the level never dropping, and increased spotting/filming on dishes
• Dispenser may remain closed with no audible actuation during the cycle

• Disconnect power at the breaker and shut off water before servicing
• Remove the door panel to access the dispenser; label and disconnect wires
• Release the old motor and install the new one in the same orientation, ensuring it seats fully
• Run a test cycle to ensure the dispenser releases rinse aid

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

Color: Black

This miniature door switch is the snap-action interlock that tells the appliance when the door is closed. Replacing a worn or sticking switch restores reliable start/stop and proper door-status sensing for safe, consistent operation. What it does:

• Acts as the latch/interlock sensor for door open/closed status
• Signals the control to allow or prevent operation based on door position
• Typical symptoms include: won't start or shows a door message, stops when the door is bumped, or light/fan behavior doesn't match door position

• 1 miniature door switch

• Disconnect power before servicing. If working on a microwave, high voltage may be present even when unplugged—properly discharge the capacitor.
• Access the latch/interlock area; note wire positions and transfer one lead at a time to the new switch.
• Use a multimeter to confirm the switch changes continuity when pressed before reassembly.

Bushing, Door spring

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks