Amana Range Parts

Fix continuous clicking or burners that won't light with this range spark module. Controls ignition sparks to all burner electrodes. Moderate DIY repair.

Microwave won't turn on or has no display? The overheat thermostat often fails and cuts power as a safety feature. DIY fix in about 10 minutes.

Replace your range door gasket to restore a tight seal and prevent heat loss. Fits worn or cracked seals so your oven door closes properly. Confirm fit.

Controls gas flow to individual burners on your gas cooktop. Located underneath the cooktop surface. Replace if valve is damaged, leaking, or fails to regulate.

Replace your electric range's surface burner control knob when cracked, worn, or missing. Restores smooth operation and a clean appearance on your cooktop.

If your range burner won't spark or ignite when you turn the knob, this burner igniter switch restores spark delivery for reliable lighting.

Seals your range broiler door to retain heat and improve cooking performance. Replace if worn, cracked, or causing heat loss. Confirm fit with model.

This stainless steel door handle mounts on the front of your range oven door. Replace if cracked, broken, loose, or discolored from daily use.

White thermostat control knob for electric ranges. Replaces broken, cracked, or missing knobs. Installs on the control panel to adjust oven temperature.

Replacement burner head for gas range cooktops. Restores even flame distribution when your original is worn, clogged, or damaged. Direct fit part.

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

Gas valve and regulator assembly for ranges. Controls gas flow to burners. Replace if cracked, leaking, or damaged to restore safe gas delivery.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Adjustable leveling foot that stabilizes and levels your appliance on uneven floors to stop rocking and improve overall stability. Simple replacement for a worn or damaged foot to restore a solid, level setup. What it does:

• Threads into the appliance base to support weight and set the appliance height
• Lets you level the appliance to stop rocking or tilting on uneven floors
• Helps reduce vibration and shifting during operation
• Common symptom fix: appliance wobbles, is unlevel, or rocks when pushed

• Disconnect power and pull appliance away from the wall before working underneath
• Support the appliance so it cannot tip; adjust the foot by turning until the unit is level
• Recheck level front-to-back and side-to-side; tighten any retaining hardware if present
• If rusted or stuck, use penetrating lubricant and proper tools; avoid forcing parts in a way that could damage the cabinet

Mounting screw secures panels, brackets, and trim to the appliance frame. Replace if screw is stripped, missing, or damaged to restore secure fastening.

White control knob for gas range burner or oven valve adjustment. Replaces worn, cracked, or missing knobs. Restores secure grip and precise control.