Need Help?
Call or text
Replacement door hinge for electric and gas ranges. Supports door weight and ensures proper alignment. Needed when spring breaks or hinge arm cracks.
I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more
Metal hinge assembly that mounts to the oven door frame, enabling smooth opening and closing. Replace if cracked, broken, or no longer holding door securely.
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more
Replacement passive door hinge for electric and gas ranges. Serves as the pivot point for your oven door. Replace if bent, broken, or worn from use.
Replacement hinge for range oven doors. Allows door to open and close smoothly while supporting its weight. Needed when hinge is broken, bent, or worn.
Replaced the hinge and receiver. Read more
Supports your range oven door for smooth opening and closing. Replace if your hinge is cracked, bent, or worn, causing the door to sag or misalign.
Replace two door hinges works great now. Read more
Mounts to the range frame to anchor the door hinge arm. Replace if cracked, bent, or worn to restore proper door alignment and smooth operation.
Oven door hinge supports the door and allows smooth opening and closing. Replace if cracked, broken, or if door sags or won't stay in position.
I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more
Left-side oven door hinge that supports and controls door movement. Replace if hinge is cracked, broken, or door won't close flush, allowing heat to escape.
The replacement hinge unit arrived in just two days. The JennAire (Maytag) oven door is fairly typical in that it easily lifts off of the hinge bars. Once the door is off then removing two screws is all that's required to remove the hinge unit from the oven. The new hinge slides up into place and while you hold it up inside of its location putting the old screws back in is very easy. After sliding the door back down onto the hinge bars the oven is as good as new Read more
Replacement hinge for range oven doors. Sold individually; doors use two hinges. Replace if door won't stay closed, drops too fast, or is misaligned.
I had to take out the bottom drawer that holds pans. Disconnect the power and pull the oven out. Removed door, rear panel that held the screws for the side panel and lift up and out the side panel. After that it was straight forward as to replacing the hinge. Spent more time cleaning the florr where the oven was than installing the hinge. Read more
Supports and pivots your wall oven door for smooth opening and closing. Replace if worn, broken, or causing misalignment that prevents proper sealing.
Door hinge replacement and of course a new fuse. All went very well. Good service and tech support from AppliancePartsPros.com Read more
Stainless steel door hinge assembly for gas range ovens. Supports door weight and maintains proper alignment. Replace if bent, worn, or damaged.
Supports and pivots your range door for smooth opening and closing. Replace if hinge is cracked, broken, or worn to restore proper door alignment and secure latching.
Supports and guides your range oven door for smooth opening and closing. Replace if hinge is bent, broken, or worn causing door misalignment or drooping.
With part ordered from your website. Read more
Drawer hinge for gas ranges. Installs on storage or warming drawer to support opening and closing. Replace if hinge is cracked, broken, or worn.
Usually ships within 4 - 14 days