Parts for Speed Queen ATEE9ASP175TW01: Base / Side Panels / Rear Panel Parts

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This shipping plug is a small protective cap that seals an appliance opening during transport and storage to prevent dirt, moisture, and shipping damage. It helps keep internal components clean until installation or first use. What it does:

• Covers and seals a designated opening or port during shipping to prevent debris intrusion
• Protects exposed fittings and seals from damage while appliance is moved
• Keeps travel-related contaminants out of the drum/tub area or service ports
• Makes it easy to spot and remove before use to avoid operating with the plug installed

• One shipping plug/cap as shown

• Remove and discard the shipping plug before connecting water, power, or operating the appliance
• If used during service, ensure the mating opening is clean before reinstalling any permanent fittings
• Follow manufacturer instructions for proper removal; wear gloves to protect hands when pulling tight-fitting plugs
• For safety, disconnect power and water supply before doing any service that requires accessing internal components

This replacement rubber foot cushions the machine's contact point with the floor to improve stability, reduce vibration, and protect surfaces. Replace a worn or missing foot to restore steadier, quieter operation and easier leveling.

• Provides a cushioned, non-slip contact point between the appliance and floor
• Helps absorb vibration and reduce rattling or movement during cycles
• Aids in proper leveling and overall stability
• Replace when cracked, flattened, or missing, or if the unit rocks or "walks"

• Disconnect power; for washers, also turn off water. If applicable, shut off gas supply
• Carefully tilt or raise the appliance with assistance and proper lifting support
• Remove the worn foot and install the new foot on the leveling leg or base as designed, ensuring it seats fully
• Re-level the appliance and tighten any locknuts; verify stable operation

The Pressure Sensor is an OEM part for Speedqueen commercial washers. It plays an important safety role by actively monitoring water levels and pressure changes within the washing machine. Located internally, the sensor communicates water level status to the control module.

Causes of a bad pressure sensor can include failure or degradation of electronic components over time. Damage from impact or liquid ingress may also cause sensors to malfunction.

Symptoms of a bad Pressure Sensor include:

• Erratic or inconsistent water levels during fills and drains
• Inability to detect rises or falls in water pressure
• Fault codes or error messages on the control panel
• Safety issues from unregulated water valves

This replacement porcelain touch-up paint restores small chips, scratches and worn spots on enamel-coated appliance surfaces to help improve appearance and slow surface corrosion. Easy to apply for spot repairs. What it does:

• Covers small chips, scratches and scuffs on porcelain/enamel surfaces
• Helps protect exposed metal from moisture that can lead to surface rust
• Matches factory finish color on compatible porcelain-coated panels (spot repairs only)
• Useful for finishing edges around dings and improving visual appearance

• One bottle of porcelain touch-up paint

• Clean and dry the repair area thoroughly; remove loose paint and rust before applying
• Test paint in an inconspicuous spot to confirm color match and adhesion
• Apply sparingly with a fine brush or applicator; allow recommended drying time between coats
• Keep away from open flame; store and dispose of per local regulations; keep out of reach of children