Parts for Speed Queen ATEE9ASP175TW01: Dryer Loading Door-Model Atee9agp173tw01 Parts

A replacement wedge for the door handle that restores a secure grip and smooth door operation. Fits the white trim area of the handle assembly to replace cracked, broken, or worn wedges and improve door feel. What it does:

• Replaces a damaged or missing wedge piece that holds the door handle trim in position.
• Restores a stable gripping surface so the door opens and closes without slipping.
• Helps correct symptoms such as a loose, cracked, or partially detached handle wedge.
• Matches the white finish used on the handle trim for a consistent appearance.

• One white wedge door-handle piece as shown

• Disconnect power to the appliance before starting any repair.
• Installation typically requires basic hand tools; remove the handle/trim to access the wedge.
• Align the wedge and snap or fasten into place without forcing; avoid over-tightening fasteners.

This is a replacement window door package designed to restore the washer door assembly so you can safely view cycles and keep the front of the machine sealed during operation. It replaces a worn, cracked or cloudy door assembly. What it does

• Provides a clear viewing window so you can check load condition without opening the washer
• Replaces cracked, damaged, or cloudy door panels that can obstruct visibility
• Helps maintain the front seal area to reduce splash and water escape during cycles
• Restores proper door fit and operation when worn or damaged components affect closure

• One window door package

• Disconnect power and water, and follow the manufacturer's service manual before starting
• Basic tools typically required; some models may need trim/clips removed to swap the assembly
• Inspect door gasket and latch during replacement; replace if damaged to ensure a proper seal

This replacement dryer window door glass restores the clear viewing window and protective barrier on compatible Speed Queen dryer doors. It lets you check load condition at a glance while maintaining the door's seal and appearance. What it does:

• Replaces cracked, chipped or fogged door window glass to restore a clear view into the drum
• Serves as the protective barrier between the drum and the outer door panel
• Helps maintain the door's insulating barrier and prevents lint/dust entry around the opening
• Returns the door to a finished, safe condition after impact damage

• One replacement dryer window door glass

• Disconnect power to the dryer before starting any disassembly
• Handle glass with gloves and eye protection; glass edges may be sharp
• Typically requires removing the outer door panel or inner trim to swap the glass
• Inspect door gaskets, clips, and mounting hardware; reuse only parts that are undamaged

This door strike bracket mounts to the cabinet and positions the door strike so the door latches securely and the machine recognizes a closed door. Replace a bent or broken bracket to restore proper door alignment and reliable starts.

• Supports and aligns the door strike with the latch/lock assembly
• Ensures the door switch/interlock is engaged when the door is shut
• Helps prevent nuisance "door open" messages and cycles that won't start
• Direct replacement for a damaged, bent, or missing bracket

• Disconnect power before servicing; shut off water or gas supplies if applicable
• Open the door and access the bracket from the front panel area
• Note bracket orientation; transfer and install using existing hardware; align before tightening
• After reassembly, the door closes firmly and the machine starts without a door error

Sturdy metal door strike that mates with the latch/lock on your machine's cabinet. It keeps the door closed and engages the door switch so cycles can start and run without nuisance stops.

• Interfaces with the door latch/lock mechanism to secure closure
• Engages the door switch/interlock so the appliance can start and continue running
• Restores proper door alignment and latch feel after wear or bending
• Typical symptoms: door won't latch or pops open; unit won't start/run; intermittent stopping mid-cycle; visible damage to the strike

• Unplug the appliance (and shut off gas to gas dryers) before servicing
• Remove the existing strike and retain mounting hardware; note orientation
• Install the new strike in the same position; tighten screws and verify alignment
• Close the door to confirm smooth latching and proper operation

This is a 10-24 x .488 Phillips flat-head machine screw used to fasten appliance components securely. It replaces missing or damaged screws to restore proper fit and reduce vibration and loose panels. What it does:

• Fastens panels, brackets, or components where a 10-24 machine screw is specified
• Restores secure connections to stop rattling or misalignment caused by missing screws
• Replaces stripped or corroded screws to maintain safe, stable assembly

• Disconnect power and follow all safety precautions before servicing the appliance
• Start the screw by hand to avoid cross-threading; use the correct size Phillips driver
• Tighten snugly but do not overtighten—excessive torque can strip threads or damage parts
• If threads are damaged, repair or replace the mating fastener or insert before installing

This door liner seal provides a watertight barrier between the washer door and tub, helping prevent leaks and keeping laundry contained during cycles. Designed as a direct-replacement service part for compatible Speed Queen front-load washers. What it does:

• Seals the gap between the door and the tub to stop water from escaping during wash and rinse cycles
• Helps maintain proper drum containment and reduces water on the door opening
• Commonly replaced when you see visible wear, tearing, or persistent leaking from the door area
• Compatible with OEM door assembly designs that use a packaged liner seal

• Follow manufacturer instructions for proper seating and clamping
• Inspect surrounding door boot and latch for damage; replace if worn to ensure a proper seal
• Disconnect power and water supply before starting work to reduce risk of shock or flooding
• Test with a short cycle and check for leaks after installation

This grill door liner is the inner-facing trim piece that restores the dryer/grill door's appearance and protects the door opening from wear. It replaces cracked, warped, or discolored liners to give a clean, finished look. What it does:

• Covers and protects the door opening edge from heat, lint, and everyday wear
• Restores a smooth, uniform interior door surface after damage or discoloration
• Helps keep the door seal area aligned and reduces gaps where lint or debris can collect
• Improves appliance appearance when the original liner is cracked, warped, or peeling

• One grill door liner (white)

• Designed to fit the original mounting points; inspect existing hardware and retain any reusable clips/screws
• Turn off and unplug the appliance before starting work; allow surfaces to cool
• Use basic hand tools; avoid forcing the liner into place to prevent cracking

This is a 8-AB-16 x 3/4 Phillips truss-head screw used to fasten appliance panels and components. It provides a low-profile, wide bearing surface to hold trim, guards, and light assemblies securely. What it does:

• Fastens panels, trim pieces, brackets and lightweight assemblies
• Wide truss head distributes load to prevent surface damage
• Phillips drive for common screwdriver or bit compatibility
• Helps stop rattling or loose panels when a worn or missing screw is replaced

• Use the correct #2 Phillips driver to avoid stripping the head
• Thread into original hole; do not force if threads feel damaged
• Tighten snugly but avoid overtightening to prevent stripping or cracking surrounding material
• Keep removed hardware organized for reassembly; replace any damaged mating parts

This door hinge secures and lets the appliance door pivot smoothly, restoring proper alignment and reliable opening/closing. A direct-fit replacement designed to return worn or damaged hinges to correct function. What it does:

• Supports the door and provides a pivot point for opening and closing
• Restores proper door alignment and prevents sagging or uneven gaps
• Helps the door latch and seal correctly by maintaining hinge position
• Common symptom fix: loose, noisy, tilted, or non-closing door

• Disconnect power and water before beginning any repairs
• Support the door during removal/installation to prevent dropping or damage
• Use the factory mounting screws and torque to OEM spec; replace damaged fasteners
• If alignment or latch issues persist after install, check strike and door seal for wear or damage