Parts for Speed Queen ATEE9ASP175TW01: Outer Tub / Front / Clamp Ring Parts

A small rubber pressure bulb that connects to the washer's air hose to help the machine detect and control water level. Replaces a cracked or collapsed bulb to restore reliable fill and spin cycles. What it does:

• Senses water level changes by transmitting air pressure to the washer's pressure switch
• Helps the washer start and stop filling at the correct levels
• Commonly fails when cracked, hardened, or leaking, causing overfill, underfill, or no-fill symptoms
• Works with the machine's pressure tubing and switch to maintain proper cycle operation

• One pressure bulb

• Disconnect power and turn off water before starting any repair
• Inspect and replace any damaged tubing when installing the bulb for a secure air-tight fit
• Avoid sharp bends or pinches in the air hose; ensure connections are properly seated

This pressure sensor assembly detects water pressure to monitor and control washer water level, helping the machine fill and drain correctly. Replaces a failed pressure sensor to restore accurate fill sensing and cycle operation. What it does:

• Senses tub water pressure and signals the control to start/stop filling
• Helps prevent overfill or underfill conditions when functioning correctly
• Commonly replaced for symptoms like incorrect water level, continuous filling, or fill/drain errors
• Works with the washer's air line/tub pressure system to report water level

• Disconnect power and turn off water supply before beginning service
• Note tubing routing and electrical connector orientation; photograph before removal
• Handle sensor and vacuum/air line gently to avoid kinks or damage
• Test washer through a short cycle after install to confirm correct operation

Note: This part includes one shock with instructions.

The Shock Assembly Kit is an OEM part for Speed Queen washing machines. It is a comprehensive kit that includes one shock absorber and the necessary mounting hardware. This shock absorber plays a vital role in absorbing shocks and vibration during the spin cycle.

Symptoms of a bad shock absorber include:

• Excessive shaking or vibrating during operation  
• Loud banging noises occurring during spinning
• The washer moving or walking on the floor during use
• Leaks developing due to added stress on components

Causes of a bad shock absorber can include wear and tear over time, exposure to heavy loads that strain the system, or damage due to impact. 

This OEM replacement is also compatible with Whirlpool, Maytag, Amana, Roper, and some Kenmore models. With its durable design and tight fittings, the Shock Assembly effectively minimizes machine movement to reduce noise and protect components.

This front outer tub houses the inner wash basket and retains wash water, restoring structural support and a watertight enclosure when the original tub is cracked or damaged. Fits Speed Queen top-load washers. What it does:

• Provides the structural support for the inner basket and suspension assembly.
• Holds and directs wash and rinse water to prevent leaks into the cabinet.
• Replaces a cracked, warped, or corroded front tub that causes visible leaks.
• Helps reduce excessive vibration or rubbing caused by a damaged tub surface.

• Disconnect power and shut off water supply before beginning service.
• Drain the washer and support or remove the inner basket/some components as required; this part typically requires partial disassembly.
• Inspect and replace associated seals, gaskets, or fasteners as needed.
• Follow the OEM service manual.

This replacement deflector channels airflow and shields internal dryer components to help maintain consistent drying and protect the blower area from debris. A direct-fit service part for affected Speed Queen coin-op and commercial dryers. What it does:

• Directs and shapes airflow through the blower/tub area to support even drying.
• Protects the blower and nearby components from lint, small debris and direct contact.
• Helps reduce rubbing or scraping noises caused by airflow misdirection or loose parts.
• Supports normal venting to prevent localized heat buildup around the blower.

• Disconnect power (and gas, where applicable) before starting any repair.
• Wear gloves and eye protection; avoid sharp edges around the cabinet and blower housing.
• Remove the dryer cabinet or access panel per OEM instructions to access the deflector.
• Reassemble panels and test operation after installation; check for proper airflow and unusual noises.

This outer tub front seal forms a watertight barrier at the front of the washer's outer tub to help prevent leaks and maintain proper tub operation. It replaces a worn or torn front seal to stop visible leaking and reduce water loss. What it does:

• Seals the gap between the outer tub and the front access area to prevent water from escaping during fill and spin cycles
• Helps maintain proper tub alignment and reduces water intrusion into the cabinet
• Commonly replaced when the seal is cracked, hardened, torn, or leaking at the front of the tub
• Can help stop surface pooling around the washer door or base

• One outer tub front seal

• Disconnect power and water supply before starting; drain the tub and move the washer to a safe work area
• Replacement requires access to the washer cabinet and removal of the front components; use appropriate tools and follow the washer's service manual
• Inspect the tub lip, shaft, and surrounding components for damage or excessive wear and replace as needed

This clothes guard deflector installs on the dryer drum to help guide and protect garments during tumbling. It restores smooth airflow and drum rotation for safer, more reliable drying. What it does:

• Directs clothes away from gaps and openings to reduce snags and fabric damage
• Helps maintain proper tumbling and airflow inside the drum
• Replaces a worn or missing deflector that can cause rubbing marks or redirected garments
• Matches OEM fit and mounting points for straightforward replacement

• Disconnect power to the dryer before starting any work.
• Access the mounting area per the dryer service manual (panel or drum removal may be required).
• Use basic hand tools and handle the part gently to avoid deforming mounting tabs.

This front tub assembly is the outer wash tub section that supports and seals the washer drum, restoring proper water containment and tub alignment for top-load machines. Use when the outer tub is cracked, leaking, or misaligned. What it does:

• Replaces the front/outer wash tub to restore a watertight enclosure for the inner drum
• Supports the drum and provides mounting surfaces for seals and suspension components
• Helps stop leaks from cracks or damage in the front tub area
• Restores correct tub alignment that can reduce vibration and noise when worn or distorted

• Designed for qualified DIYers; refer to the machine's service manual
• Power and water must be disconnected before beginning any repairs
• Inspect and replace associated seals, gaskets, or mounting hardware as needed
• Test for leaks and proper spin/balance after reassembly