Parts for Ge DPVH890EJ2MG: 06 - Blower & Drive Assembly Parts

The GE clamp and screw kit is an OEM replacement part responsible for securing the dryer blower wheel in place. This kit consists of two clamps and a screw, designed to ensure the blower wheel remains firmly attached to the motor shaft. The clamp maintains the blower wheel's stability and prevents it from coming loose during the drying process. The blower wheel creates the airflow necessary to circulate hot air and efficiently dry clothes.

Over time, clamps and screws can become loose or corroded due to regular use, vibrations, or exposure to moisture. Improper handling during maintenance or repairs can also lead to damage or loss of these small but essential parts.

Symptoms of a bad Clamp and Screw Kit include:

• Loose or rattling components within the dryer
• Parts becoming misaligned or detached
• Unusual noises during dryer operation
• Difficulty in securing dryer parts during repairs

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The GE clamp and screw kit is an OEM replacement part responsible for securing the dryer blower wheel in place. This kit consists of two clamps and a screw, designed to ensure the blower wheel remains firmly attached to the motor shaft. The clamp maintains the blower wheel's stability and prevents it from coming loose during the drying process. The blower wheel creates the airflow necessary to circulate hot air and efficiently dry clothes.

Over time, clamps and screws can become loose or corroded due to regular use, vibrations, or exposure to moisture. Improper handling during maintenance or repairs can also lead to damage or loss of these small but essential parts.

Symptoms of a bad Clamp and Screw Kit include:

• Loose or rattling components within the dryer
• Parts becoming misaligned or detached
• Unusual noises during dryer operation
• Difficulty in securing dryer parts during repairs

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Blower Wheel is an OEM replacement part for GE dryers. It has a role in the air circulation within the dryer, aiding in the even and efficient drying of clothes. The blower wheel, connected to the motor, helps in expelling the moist air out of the dryer through the exhaust vent during the drying cycle.

Causes of a malfunctioning blower wheel are typically wear and tear from regular use, the accumulation of lint or debris, or damage to the wheel’s fins or central hub, which can impact its rotation and air circulation capability.

Symptoms of a bad Blower Wheel include:

• Unusual noises during operation
• Extended drying times
• The dryer overheating
• Reduced air circulation

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This motor strap secures the appliance motor to the cabinet, keeping the motor stable during operation to reduce vibration and noise. Use this replacement to restore proper motor positioning and support in compatible models. What it does:

• Holds the motor firmly in place to prevent movement or shifting during use
• Helps reduce vibration and associated noise caused by a loose motor
• Maintains correct motor alignment so belts and linkages run smoothly
• Commonly used when a worn or broken strap allows motor sag or misalignment

• One motor mounting/retaining strap

• Disconnect power to the appliance before beginning any work
• Inspect mounting points and fasteners; replace any damaged hardware as needed
• Secure strap to the motor and cabinet using the original mounting holes and recommended hardware

This motor support is the mounting bracket that holds the dryer motor and aligns the blower assembly, restoring stable motor positioning for reliable drum rotation and airflow. Replaces a worn or damaged support to reduce noise and vibration. What it does:

• Secures the dryer motor and blower housing to maintain correct alignment for the drive system
• Helps prevent excessive motor movement that can cause squealing, rubbing or grinding noises
• Restores proper blower alignment to improve airflow and drying performance when support is damaged
• Needed if the dryer drags, vibrates, or makes unusual noises during operation

• Motor support bracket (1)

• Disconnect power to the appliance before starting any repair
• Removal typically requires taking off the dryer front panel and/or drum; follow model-specific disassembly instructions
• Inspect surrounding components (motor, blower wheel, mounting hardware) and replace any damaged fasteners as needed

The Drive Belt is an OEM replacement part for GE dryers. It functions as the critical linkage connecting the dryer drum to the motor. Reliable belt operation is essential for tumbling clothes and continuous airflow through the dryer.

Causes of a bad drive belt include wear from years of operation, damage from improper cleaning or maintenance, or fraying/cracking from excessively heavy loads.

Symptoms of a bad drive belt include:

• The dryer drum failing to spin or turn sluggishly during cycles
• Vibration or loud clunking noises coming from inside the dryer
• The inability of the dryer to progress past the initial cycle stages

This OEM GE part is also compatible with some Hotpoint, RCA, and select Kenmore dryer models.

The Idler Pulley is an OEM component specifically designed for GE dryers. As part of the drum assembly, the idler pulley helps drive the rotation of the drying drum. It works closely with the belt and motor pulley to spin the drum and tumble clothes during the drying cycle.

Causes of a bad idler pulley can include wear and tear of moving parts over time, loose or worn belts that cause added strain, or damage from sticking or jamming during operation. 

Symptoms of a bad idler pulley include:

• The dryer drum not spinning or tumbling clothes
• Loud grinding or squealing noises coming from inside the dryer 
• The belt slipping off the pulleys
• Vibration or shaking during use

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This exhaust duct channels cooking exhaust from the appliance to the home vent system, restoring proper airflow and helping reduce smoke, steam and cooking odors in the kitchen. What it does:

• Directs exhaust air from the appliance to the venting system to maintain proper airflow.
• Helps reduce cooking smoke, steam and odors by providing a clear path to the outside.
• Prevents moisture buildup and improves ventilation performance when intact and properly installed.
• Worn, crushed or disconnected ducts can cause weak exhaust, lingering odors, excess steam or increased noise.

• Disconnect power to the appliance and follow all safety and grounding instructions before servicing.
• Use basic hand tools and gloves; avoid sharp edges on metal ducting.
• Do not modify the part; if replacement requires changes to venting, refer to the appliance manual.

This ground screw secures the appliance chassis ground connection to the cabinet, restoring a reliable earth path for safe operation and reducing risk of electrical faults. Simple replacement keeps electrical components properly grounded. What it does

• Secures the ground wire or grounding strap to the appliance chassis to maintain a safe earth connection.
• Restores proper grounding when the original screw is missing, loose, or corroded.
• Helps prevent intermittent power/grounding issues and reduces risk of electrical arcing at the chassis connection.
• Works wherever a dedicated grounding point is required on the cabinet or frame.

• Single ground screw

• Always disconnect power (unplug or switch off circuit breaker) before servicing electrical connections.
• Verify chassis is de-energized and wear appropriate PPE when working on electrical parts.
• Use the correct driver bit and size to avoid stripping the screw; tighten securely but avoid over-torquing.
• Replace corroded grounding hardware and ensure the ground wire/strap has clean metal-to-metal contact.

This outlet backup thermostat for dryers mounts on the exhaust duct and provides secondary over-temperature protection. It shuts the heater off if exhaust air gets too hot, helping maintain safe, consistent drying.

• Serves as a secondary temperature limit on the exhaust/outlet duct
• Opens the heater circuit if exhaust temperature rises too high
• Failure symptoms include no heat, intermittent heat, overheating, or short-cycling
• Replace if it fails continuity testing or shows heat damage

• Disconnect power and shut off gas supply (for gas models) before servicing
• Access the outlet/exhaust duct per your model; transfer wires one at a time and secure the thermostat to the duct
• Replace any heat-damaged connectors and correct restricted airflow (clean lint filter and vent) before testing
• Match the color/rating to your original; this is the orange variant

This is a genuine GE replacement screw used to secure appliance panels and components, restoring proper fit and reducing vibration or rattling. A simple fastener that helps keep assemblies aligned and functioning safely. What it does:

• Secures panels, brackets, and small components in place
• Prevents noise from loose parts and maintains structural alignment
• Restores proper fastening after repairs or wear
• Matches OEM fit for reliable replacement

• Disconnect power to the appliance before accessing internal parts
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully and tighten until snug; do not overtighten to prevent damage
• Replace any damaged or missing fasteners with the same OEM part for best results

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.

The Outlet Control Thermistor is an OEM part for GE dryers. This thermistor monitors and regulates the temperature inside the dryer by sending temperature readings to the control board, ensuring the dryer operates at optimal temperatures for efficient drying and preventing overheating.

Causes of a bad outlet control thermistor can include wear and tear from regular use, electrical malfunctions, or exposure to excessive heat.

Symptoms of a bad outlet control thermistor include:

• The dryer overheating or not heating at all
• Inconsistent drying times
• The dryer shutting off prematurely
• Error codes related to temperature issues

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

A small rubber-lined washer that cushions and electrically isolates connections to reduce metal-on-metal contact and damp vibration. Helps protect parts and maintain proper spacing for reliable operation. What it does:

• Cushions fasteners and mounting points to reduce vibration and noise
• Provides electrical insulation between metal components
• Prevents wear from direct metal-to-metal contact
• Keeps assemblies aligned by maintaining correct spacing

• Disconnect power to the appliance before servicing
• Access the mounting area per your model's service instructions
• Replace with the same style and orientation to ensure proper fit and insulation
• Inspect surrounding hardware and replace any damaged fasteners or worn mounting surfaces

A replacement spring idler that provides the tension needed to keep the dryer drive/idler assembly aligned so the drum and belt run smoothly. Restores proper belt tension to help reduce slipping and noisy operation. What it does:

• Applies tension to the idler pulley so the drive belt stays engaged with the motor and drum
• Helps prevent belt slippage that can cause the drum to stop turning or turn intermittently
• Reduces squealing or grinding noises caused by a loose or misaligned belt/idler
• Supports consistent drum rotation for efficient drying performance

• 1 spring idler (tension spring) as pictured

• Disconnect power to the appliance before beginning any repair
• Replace only with the exact part number for your unit;
• Basic hand tools are typically required;
• If you find damaged pulleys, belt, or excessive wear, inspect those components and replace as needed

This idler pivot screw secures the dryer idler assembly so the belt stays properly tensioned for smooth drum rotation. It's a small but critical mounting fastener for the idler/pulley system. What it does:

• Secures the idler/pulley pivot to the dryer chassis so the tensioner can hold the drive belt.
• Restores proper belt alignment and tension when the original pivot screw is missing or worn.
• Helps stop belt slippage and related noise when the idler assembly is loose.
• Works with the idler/pulley components to allow even, stable drum rotation.

• One idler pivot screw

• Disconnect power (and gas, if applicable) before accessing internal dryer parts.
• Basic hand tools required; retain small fasteners to avoid loss during reassembly.
• If the idler or pulley shows wear, inspect and replace the entire idler assembly rather than only the screw.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

This dryer drive motor and pulley assembly powers both the drum and the blower wheel. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads consistently.

• Provides rotational power to the drum via the drive belt
• Drives the blower wheel to move air through the drum and exhaust
• Common failure symptoms: dryer hums but won't start; drum won't turn; runs briefly then shuts off
• Also addresses loud humming, squealing, or grinding from the motor area

• Disconnect power; if gas, shut off the gas supply before servicing
• Remove front panel, release belt tension, and lift out the drum to access the motor
• Note wire locations; transfer the blower wheel and any mounting brackets or clips from the original motor if your model requires it
• After reassembly, rotate the drum by hand to ensure free movement and belt alignment before restoring power

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit