Bolens Parts

Replace your lawn tractor's blade spindle shaft if blades won't engage, spin unevenly, or make grinding noises. Bearings sold separately. DIY-friendly repair.

Needle bearing for lawn tractors and mowers. Replace when you notice unusual noise, vibration, or rough movement. Confirm fit with your model number.

Flange bearing for lawn tractors and walk-behind mowers. Replace if you notice excessive noise, vibration, or wheel wobble. Verify fit with your model number.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

Sealed ball bearing reduces friction between fixed parts and rotating shafts. Replace if you hear grinding noise or notice wheel wobble. Verify fit.

Replacement 22-inch cutting blade for walk-behind mowers. Restores cutting performance when blade is dull, bent, cracked, or damaged from impacts.

Control cable for edgers. Connects the handle controls to the engine or blade mechanism. Replace if cable is frayed, broken, stretched, or disconnected.

Control cable that connects the handle lever to the auger clutch mechanism on gas snowblowers. Replace if cable is frayed, snapped, or stretched.

This control cable is a mower part that works with the control handle or lever bar that engages the wheels. It is also known as choke cable, brake cable, choke control, and control assembly cable. The inner wire total length is 53 inches, and the cable casing or conduit length is 40 inches. The control cable can stretch over time and it will result in a mower that moves forward slower than usual. A cable that's too corroded won't be capable of moving the drive lever. A broken or cut cable won't make the mower move. Here is a manufacturer-approved replacement control cable that's easy to install. A genuine OEM replacement part, this control cable is made to fit specific models of walk-behind mowers from Bolens, Ryobi, MTD, Troy-Bilt, and Yard-Man. It is sold individually.

Control cable for gas walk-behind mowers. Installs to operate speed control or drive engagement. Replace if cable is frayed, broken, or stretched.

Control cable for walk-behind mowers. Connects control handle to blade brake system. Replace if cable is damaged, frayed, broken, or won't release brake.

Thumb screw that secures the air cleaner assembly on lawn mower and small engines. Replace if damaged, stripped, or missing due to vibration.

Rope won't retract or gets stuck when pulling? This recoil starter spring restores smooth pull-and-retract action on walk-behind mowers and tillers.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

Snowblower won't start or shuts off unexpectedly? This ignition switch controls engine power. Direct replacement part restores reliable starting.