Bolens Parts

Auger bearing for snow throwers supports rotating shaft movement. Replace if you hear grinding noise or auger doesn't spin smoothly. Verify fit with model.

Drive belt for lawn tractors and riding mowers. Replace if worn, cracked, or slipping during operation. Verify fit with your model number.

Grass catcher bag for walk-behind mowers. Attaches to cutting deck frame to collect clippings. Replace if torn, worn, or damaged for proper collection.

This is a Briggs & Stratton Original Equipment 491588S Air Filter Cartridge. The purpose of this filter is to prevent dirt, dust, and debris from contaminating the carburetor and damaging the engine. This flat panel style, pleated paper air filter provides the first line of defense against the destructive effects of dirt ingestion. It is designed for 3.5 through 6.75 HP quantum engines and 625-1575 series engines. Over time, the air filter can get clogged or damaged, and this can lead to reduced engine performance. Locate the air filter cover, unscrew it, and remove the old filter. Make sure to clear out any debris that has found its way into the air filter assembly before inserting the new cartridge. Reattach the air filter cover and secure it with the screws. This replacement part works with generators, lawnmowers, pressure washers, wood chippers, and tillers. Aside from Briggs & Stratton, it is also compatible with specific products from Craftsman, Husqvarna, Lawn-Boy, Toro, Troy-Bilt, Simplicity, Snapper, and Wheel Horse. It is a genuine OEM replacement part and is sold individually.

The exhaust systems on lawn and garden equipment are just as important as those on a vehicle. They need a good seal to prevent a leak between the carburetor and the exhaust tube, which would allow air leakage that could cause performance issues and loud noise. Over time all exhaust gaskets deteriorate and require a full replacement. It is relatively easy to replace an exhaust gasket and requires only the use of screw drivers, a socket set or a wrench set depending on the device being service. Replacement components such as sockets or screws may also be required during this repair. The gasket surfaces should be cleaned and fully dried before being installed between the carburetor and the exhaust tube. This exhaust gasket works with Toro, Simplicity, Murray and Briggs & Stratton lawnmowers, generators, snowblowers, wood chippers, and lawn tractors. It also works with equipment made by Craftsman, Husqvarna, Cub Cadet, Poulan, Wheel Horse, MTD, Ariens, and more.

This front cover assembly is a replacement part for select push mowers. The part is sometimes called a front axle cover, and it serves a simple but important purpose. The cover is meant to protect the axles on the front of the mower from potential damage. If this part is broken or attached improperly, it could make pushing the mower more difficult. It could also expose the axle to damage.The assembly is made from high-quality plastic. However, it could start to wear down and break over time, which would require a replacement. Additionally, there is the possibility that the cover could be damaged while mowing if the user runs into a stump, large rock, or other material. When working on the mower, owners should always make sure that the engine has cooled. Replacement is relatively simple and should not take more than 15 to 20 minutes.The front cover assembly works on certain push mowers from Bolens, Yard Machines, and Columbia. This is a genuine OEM replacement part that has been sourced from the manufacturer. It is sold individually.

Replace your lawn mower's worn or broken wheel assembly with tire. Direct fit for damaged wheels that crack, wear down, or go missing over time.

These quality tiller tines are used on a variety of yard tillers. Tiller tines are blades attached to the tiller that turn soil and prep it for cultivating a garden. As the tiller tines are used, they can become worn down, broken, or damaged through use or impact with rocks and other debris. These are C-shaped tines that can cut through dense soil.If the tiller tines are bent, dull, or damaged, they will need to be replaced, otherwise they might till the soil unevenly and may not reach the depth required. To replace the tines, remove the spark plug wire before taking off the tine shield end cover. Taking out the tines requires removing the cotter pin from the clevis pin so the clevis pin can be pulled out. Next, the tines can be pulled directly off of the shaft. Slide on the new tines and reinstall the clevis and cotter pins before using the tiller again.These tiller tines are an authentic OEM replacement part directly sourced from the manufacturer. It is sold as an individual part. The tines are compatible with tillers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Bolens, Yard Machines, MTD, Huskee, and Montgomery Wards.

Replace your snow thrower's idler pulley bearing assembly when you hear grinding noises or notice belt slippage. Restores smooth operation. Verify fit with your model number before ordering.

Hex screw for lawn mowers and garden equipment. Replaces cracked, stripped, or missing hex head bolts. Six-sided head fastens metal or wood components.

Replacement screw for outdoor power equipment including lawn tractors, tillers, leaf blowers, and trimmers. Replace stripped, missing, or damaged screws.

Engine running rough or making ticking noises? A worn rocker arm stud can affect valve timing. This replacement stud restores proper valve operation.

Hex head screw fastener for walk-behind lawn mowers. Secures components and housing parts. Replace if stripped, rusted, or missing for proper assembly.

The hex head self-tapping screws are designed for a number of applications in lawn and garden equipment, primarily holding machinery and engine parts together. Over time, screws can become stripped, fall out, or otherwise get damaged, resulting in a need for replacement. When replacing screws and other hardware, always be sure to disengage or disable any power supply to reduce the risk of shock or other injuries. The self-tapping screw makes it easy to replace, and the fact that they are manufacturer-guaranteed ensures a perfect fit for compatible machines. This OEM self-tapping screw is compatible with several machines from RYOBI, MTD, Husky, Cub Cadet, Yard-Man, Troy-Bilt, Bolens, and Yard Machines. It can be found in lawnmowers and tractors and can be in multiple locations, depending on the exact model. This screw is sold as a single piece; order multiple quantities if needed.

Self-tapping screw for lawn mowers and garden equipment. Secures metal, wood, and plastic parts. Replace if stripped, missing, or corroded.