Parts for Frigidaire LCE772LL0: 02 - Cabinet And Component Parts

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Top panel for laundry center units. Covers and protects the upper surface. Replace if cracked, chipped, discolored, or damaged from wear and tear.

This is a small metal grounding ball that sits in the rear drum bearing area of the dryer. It helps dissipate static electricity buildup in the drum during operation. Replace this part if you are experiencing excessive static cling on clothes, static shocks when unloading laundry, or if the original ball is missing or worn.

For a complete drum bearing and shaft kit order 5303281153.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Supports the dryer drum for smooth rotation. Replace if your dryer squeals, makes grinding noises, or the drum sags. Verify fit with your model number.

This metal bracket supports the drum bearing at the rear of the dryer, helping to hold the drum in proper alignment as it rotates. It provides a stable mounting point for the bearing assembly that the drum rides on. Replace this bracket if the dryer makes squealing, grinding, or thumping noises during operation, or if the drum wobbles and does not spin smoothly.

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

Dryer stopped heating or takes hours to dry? This heating element restores proper heat output. Typical repair takes about an hour with basic tools.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Metal heat deflector that mounts near the dryer heating element. Replace if warped, cracked, or damaged to restore proper heat distribution and protect wiring.

Front drum bulkhead for dryers. Mounts inside cabinet to support rotating drum. Replace if cracked, worn, or damaged to restore proper drum rotation.

This is a felt seal that fits around the drum of a dryer, providing a soft barrier between the rotating drum and the stationary cabinet. It helps maintain proper airflow and prevents clothes from getting caught between the drum and the housing. Replace this seal if you notice scorch marks on clothing, hear squeaking or scraping noises during operation, or find lint escaping around the drum edges.

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

Replacement screw that secures panels and components in dryers, washers, and ranges. Needed when original fasteners are missing, stripped, or worn.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

A single replacement screw fastener used to secure trim, panels, or internal components. Fits specific Frigidaire appliance locations to restore proper fastening and alignment where factory hardware is missing or damaged. What it does:

• Secures plastic trim, brackets, or metal panels in refrigerators and freezers
• Restores proper alignment and prevents rattling or loose parts
• Replaces stripped, corroded, or lost hardware to maintain appliance function
• Works wherever the original factory screw was specified

• One replacement screw

• Use the correct screwdriver or bit to avoid damaging the screw head
• Do not overtighten; snug until seated to prevent cracking plastic or stripping threads
• Replace only with the exact factory part for proper fit and function
• Unplug the appliance or turn off power first if working near electrical components

Dryer drum shaft that supports the drum and connects to the bearing. Replace if worn, damaged, or causing squeaking noises. Verify fit with your model.

Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.

Specs: 8 - 18 x 0.500

This thermal fuse is a safety device that cuts power to the dryer's heating element if the internal temperature exceeds a safe limit. It is a one-time-use component that cannot be reset once tripped. Replace this part if the dryer runs but produces no heat, or if the dryer does not start at all.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

This is a heat shield insulator that mounts on the inner side of the dryer door in a stacked laundry center or washer/dryer combo unit. It prevents excessive heat from transferring through the door during drying cycles, protecting the outer door surface and improving energy efficiency. Replace this insulation if it is torn, deteriorated, or missing, which can cause the door to become excessively hot to the touch or reduce drying performance.

Replacement lamp cover for washer dryer combo control panel. Protects indicator light assembly. Order new cover if original is cracked, broken, or missing.

This part has been discontinued by the manufacturer and is no longer available.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.