Parts for Frigidaire FFFW4000QW0: 03 - Cabinet / Top Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Washer won't start, stops mid-cycle, or shows error codes? The control board manages all functions. Moderate DIY repair restores full operation.

Mounting bracket for laundry center and washer models. Secures components in place. Replace if bent, cracked, or broken to restore proper alignment.

This replacement vent manages internal airflow within your appliance, routing air through the intended path. Restoring a damaged or missing vent helps maintain performance and reduces heat and moisture buildup inside the cabinet. What it does:

• Directs and regulates airflow through the appliance's air path
• Helps maintain proper pressure balance and efficient moisture removal
• Reduces the chance of lint or debris bypassing the intended ducting
• A cracked, warped, missing, or clogged vent can contribute to weak airflow, longer cycles, excess heat, or unusual noises

• 1 vent

• Disconnect power before servicing; allow hot components to cool
• Access the vent by removing the appropriate panel; note screw and clip locations
• Transfer any mounting hardware or seals from the old vent and ensure proper orientation
• Clear lint/debris from adjoining ducts before reassembly; test run to ensure smooth airflow and no rattling

Washer won't spin or drain? Error code E47? The door lock assembly often causes these issues. This moderately easy repair typically takes 30 minutes.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This is the clear glass panel mounted inside the washer door that allows you to see your laundry during the wash cycle while creating a seal that keeps water inside the drum. It sits within the door frame and is held in place by the inner and outer door panels. Replace it when the glass is cracked, chipped, or shattered, which can cause leaks or pose a safety hazard.

Inner door frame for front-load washers. Secures door glass and seal, maintains alignment. Replace if cracked, broken, or causing door to sag or misalign.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Fix a washer that won't start or lock with a new door strike. This latch catch secures your door during cycles. Simple 2-minute DIY repair with a screwdriver.

The Washer Door Hinge is an OEM part compatible with Frigidaire washing machines. This hinge ensures the door opens and closes smoothly and securely, maintaining a proper seal during operation.

Common causes of a faulty hinge include regular wear and tear from frequent use, corrosion due to exposure to moisture, or physical damage from accidental impacts. A damaged hinge can lead to improper door alignment, affecting the washing machine’s ability to maintain a watertight seal.

Symptoms of a bad washer door hinge include:

• Difficulty in opening or closing the door
• The door not staying in place or sagging
• Leaks from around the door area
• Visible signs of rust or damage on the hinge

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

Secures hoses in your laundry center. Replace if cracked, loose, or causing leaks. Confirm fit with your model number before ordering.

Spring mounting bracket for washers. Secures suspension springs to the washer tub or frame. Replace if bracket is cracked, bent, or broken from load stress.

This is the top work surface panel that covers the upper portion of the dryer cabinet. It provides structural support and a finished exterior surface while protecting internal components from dust and debris. Replace this panel if it is dented, cracked, rusted, or if the finish is damaged.

Base for washer and laundry center models. Provides structural support and stability. Replace if cracked, broken, or damaged to restore proper installation.

Mounting screw for laundry center and washer installations. Replaces lost, stripped, or corroded screws used to secure panels and components.

Mounting bracket secures internal components and panels in your washer. Replace if bracket is cracked, broken, or missing to restore proper alignment and support.

This is an access panel that covers the internal components of a washing machine or laundry center. It provides a removable barrier for service and maintenance access while keeping the machine's interior protected during normal operation. Replace this panel if it is cracked, warped, or damaged, which can expose internal parts to dust and moisture.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.

M5 x 0.8 metric machine screw secures panels and internal assemblies. Replace missing, stripped, or damaged fasteners to restore tight fit.

Replace your washer's cracked or broken outer door panel. This white plastic cover protects the door frame and attaches at the hinge. Restores appearance.

Spring protector installs on washer suspension springs to prevent wear and damage. Replace if cracked, broken, or missing to protect suspension components.

Sound dampening insulation that reduces vibration and noise in your washer. Replace if worn, torn, or missing to restore quiet operation and protect components.

Retaining ring for washer door assembly. Fits into groove to secure and space components. Replace if cracked, worn, or missing to restore alignment.

Plastic door cover

Rubber grommet cushion for laundry center washers. Isolates vibration and prevents wear where components pass through openings. Replaces worn or missing.

This small plastic retainer clip secures trim and lightweight components so doors and shelves stay aligned and rattle-free. A simple replacement that restores proper fit where a broken or missing clip lets parts shift. What it does

• Fastens and aligns lightweight plastic trim, door, or shelf components
• Prevents movement and noise caused by a cracked or missing retainer
• Restores secure fit for loose or sagging trim pieces
• Commonly used where a push-in or snap-in fastener is required

• One retainer clip

• Inspect the mating slots or holes for damage before installing the new clip
• Push the clip into place until it snaps; the attached part seats securely
• No special tools typically required; use a flat tool to remove the old clip if needed
• Disconnect power only when working near electrical components or lighting assemblies

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Sound dampening pad for dryers. Installs inside the cabinet to reduce vibration and noise. Replace if worn, torn, or missing for quieter operation.

Wiring harness for laundry center washer. Connects electrical components throughout the machine. Replace if wires are frayed, connectors are damaged, or broken.

Plastic plug kit that snaps into washer drum bolt holes after shipping bolts are removed. Replaces missing, cracked, or broken plugs for a finished look.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.