Parts for Frigidaire FFFW5000QW0: 03 - Cabinet / Top Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Repla

Fix E53 errors, no spin, or drum not moving. This motor control board restores washer operation. DIY repair in 45 minutes with our installation video.

Replace your washer's cracked or missing access cover. Restores exterior protection, shields internal components from dust and moisture, and provides a clean finished appearance.

This replacement vent manages internal airflow within your appliance, routing air through the intended path. Restoring a damaged or missing vent helps maintain performance and reduces heat and moisture buildup inside the cabinet. What it does:

• D

Washer won't spin or drain? Error code E47? The door lock assembly often causes these issues. This moderately easy repair typically takes 30 minutes.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lif

This replacement washer door window restores a clear view into the tub on compatible front-load models and helps the door seal correctly. Replace a cracked or cloudy pane to reduce leaks and keep operation safe. What it does:

• Provides the transparent viewing window in the washer door
• Works with the door boot/gasket to help form a watertight seal when closed
• Replace if the glass is cracked, chipped, shattered, or excessively scratched/cloudy
• Common symptoms include water leaking from the door area, poor sealing/door won't close, or visible damage to the window

What's included:

• One door window glass

Install notes:

• Disconnect power and turn off water supply before servicing
• Wear cut-resistant gloves and eye protection; handle broken glass carefully
• Support or remove the door to a flat surface; separate door halves and transfer the window, noting orientation
• Clean the door boot sealing surface; seat the new glass evenly and reassemble without pinching the gasket; test for leaks

Inner door frame for front load washers. Provides structural support for door glass and components. Replace if cracked, broken, or damaged from impact.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Fix a washer that won't start or lock with a new door strike. This latch catch secures your door during cycles. Simple 2-minute DIY repair with a screwdriver.

The Washer Door Hinge is an OEM part compatible with Frigidaire washing machines. This hinge ensures the door opens and closes smoothly and securely, maintaining a proper seal during operation.

Common causes of a faulty hinge include regular wear and tear from frequent use, corrosion due to exposure to moisture, or physical damage from accidental impacts. A damaged hinge can lead to improper door alignment, affecting the washing machine’s ability to maintain a watertight seal.

Symptoms of a bad washer door hinge include:

• Difficulty in opening or closing the door
• The door not staying in place or sagging
• Leaks from around the door area
• Visible signs of rust or damage on the hinge

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet pane

Secures hoses in your laundry center. Replace if cracked, loose, or causing leaks. Confirm fit with your model number before ordering.

Spring mounting bracket for washers. Secures suspension springs to the washer tub or frame. Replace if bracket is cracked, bent, or broken from load stress.

Mounting bracket secures internal components and panels in your washer. Replace if bracket is cracked, broken, or missing to restore proper alignment and support.

This small plastic retainer clip secures trim and lightweight components so doors and shelves stay aligned and rattle-free. A simple replacement that restores proper fit where a broken or missing clip lets parts shift. What it does

• Fastens and aligns lightweight plastic trim, door, or shelf components
• Prevents movement and noise caused by a cracked or missing retainer
• Restores secure fit for loose or sagging trim pieces
• Commonly used where a push-in or snap-in fastener is required

• One retainer clip

• Inspect the mating slots or holes for damage before installing the new clip
• Push the clip into place until it snaps; the attached part seats securely
• No special tools typically required; use a flat tool to remove the old clip if needed
• Disconnect power only when working near electrical components or lighting assemblies

Back panel for laundry centers and washers. Covers the rear exterior housing. Replace if cracked, damaged, or missing to restore appearance and protect internal components.

Power cord for washer installations. Replace if your original cord is damaged, frayed, missing, or shows exposed wiring for safe appliance operation.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and center

Support bracket for dryer assembly. Mounts and secures internal components in place. Replace if cracked, bent, broken, or missing to restore proper fit.

Adjustable leveling leg threads into washer base to stabilize and level the cabinet. Replace worn, missing, or broken legs to prevent rocking and vibration.

Sleeve bearing bushing that supports rotating shafts in washers. Replace if worn, cracked, or causing noise. Reduces friction and centers components.

Replacement mounting nut that secures panels, trim, and internal components. Needed when original nut is stripped, corroded, missing, or lost during repair.

M5 x 0.8 metric machine screw secures panels and internal assemblies. Replace missing, stripped, or damaged fasteners to restore tight fit.

Replacement outer door panel for washer front-load doors. Installs around door glass. Replace if cracked at hinge, broken from impact, or warped plastic.

Spring protector installs on washer suspension springs to prevent wear and damage. Replace if cracked, broken, or missing to protect suspension components.

Sound dampening insulation that reduces vibration and noise in your washer. Replace if worn, torn, or missing to restore quiet operation and protect components.

Replace a cracked, broken, or worn washer door transition ring. This trim piece covers the gap where the door meets the cabinet for proper alignment.

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What

Rubber grommet cushion for laundry center washers. Isolates vibration and prevents wear where components pass through openings. Replaces worn or missing.

Internal wiring harness for washers. Connects electrical components within the control system. Replace if wires are frayed, connectors damaged, or harness is broken.

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does: