Parts for Frigidaire FTF5000HS0: 05 - Cabinet / Top Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Connects your washing machine to the household water supply. Replace this flexible inlet hose if cracked, leaking, or worn to restore proper flow.

Washer won't spin or shows communication error? The motor control board controls spin speed and motor functions. DIY repair in 30 minutes with video guide.

Mounting bracket for laundry center and washer models. Secures components in place. Replace if bent, cracked, or broken to restore proper alignment.

Washer won't spin or drain? Error code E47? The door lock assembly often causes these issues. This moderately easy repair typically takes 30 minutes.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This is the clear glass panel mounted inside the washer door that allows you to see your laundry during the wash cycle while creating a seal that keeps water inside the drum. It sits within the door frame and is held in place by the inner and outer door panels. Replace it when the glass is cracked, chipped, or shattered, which can cause leaks or pose a safety hazard.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Washer door strike ensures proper door closure and sealing during wash cycles. Replace if door won't latch or seal. Verify fit with your model number.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This clip is a genuine General Electric part, sold individually. It can be used as a replacement part for a dryer or a washer/dryer combination appliance. This clip affixes the toe panel to the front panel of the dryer.This clip could become damaged within the standard lifespan of a dryer; this damage could take the form of nicks, scrapes, tears, punctures, or erosion to the plastic material that reduces its functionality for a dryer. If the toe panel is coming loose from the front panel of the dryer, the clip should be visually inspected and assessed for signs of damage. If the clip is damaged, it should be removed and replaced with this genuine OEM replacement part. The replacement process is simple and will require no special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This clip is compatible with the following appliance brands: Frigidaire, Kenmore, Electrolux, Westinghouse, and Crosley.

This is the lower access panel, also called a toe panel, that attaches to the front bottom of the washer. It covers the internal components beneath the drum area and provides a finished appearance. Replace this panel if it is dented, cracked, rusted, or if the mounting tabs are broken, leaving the lower portion of the machine exposed.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This replacement screw fastens panels, brackets, and internal components so assemblies stay aligned and tight during operation. With an 8-18 thread and 0.711-inch length, it matches the original hardware for a precise, reliable hold.

• Secures panels, brackets, and internal components to the cabinet/frame
• Replaces missing, stripped, or corroded screws
• Helps reduce vibration, rattling, and gaps from loose hardware
• Restores proper alignment after service or transport

• Disconnect power and shut off water/gas before servicing.
• Support panels/components while removing and installing the screw.
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten.

Spring mounting bracket for washers. Secures suspension springs to the washer tub or frame. Replace if bracket is cracked, bent, or broken from load stress.

This is the top work surface panel that covers the upper portion of the dryer cabinet. It provides structural support and a finished exterior surface while protecting internal components from dust and debris. Replace this panel if it is dented, cracked, rusted, or if the finish is damaged.

Mounting screw for laundry center and washer installations. Replaces lost, stripped, or corroded screws used to secure panels and components.

This is an access panel that covers the internal components of a washing machine or laundry center. It provides a removable barrier for service and maintenance access while keeping the machine's interior protected during normal operation. Replace this panel if it is cracked, warped, or damaged, which can expose internal parts to dust and moisture.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.

This is a metal hinge that attaches the dryer door to the cabinet and allows it to swing open and closed. It supports the weight of the door and ensures proper alignment with the door latch. Replace this hinge if the dryer door is sagging, not closing properly, or if the hinge is cracked, bent, or has worn-out pin holes.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Mounting screw secures panels, trim, or brackets in dryers, washers, and ranges. Replace lost, stripped, or corroded screws to restore stability.

Sound dampening insulation that reduces vibration and noise in your washer. Replace if worn, torn, or missing to restore quiet operation and protect components.

Adapter component for washer door bellow assembly. Secures the rubber door seal in place. Replace if cracked, broken, or causing poor seal fit.

Rubber grommet cushion for laundry center washers. Isolates vibration and prevents wear where components pass through openings. Replaces worn or missing.

Replacement bumper for your washer. Installs to cushion and protect internal components. Order a new bumper if yours is cracked, broken, or missing.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Wiring harness for laundry center washer. Connects electrical components throughout the machine. Replace if wires are frayed, connectors are damaged, or broken.

Plastic plug kit that snaps into washer drum bolt holes after shipping bolts are removed. Replaces missing, cracked, or broken plugs for a finished look.

Wiring harness for laundry center washer. Connects electrical components throughout the machine. Replace if wires are frayed, connectors are damaged, or broken.

Plastic plug kit that snaps into washer drum bolt holes after shipping bolts are removed. Replaces missing, cracked, or broken plugs for a finished look.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Shipping bolt kit secures washer tub and suspension during transport. Install before moving to prevent internal damage, then remove before use.

Shipping bolt kit secures washer tub and suspension during transport. Install before moving to prevent internal damage, then remove before use.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.