Parts for Kitchenaid 5KSM6583CBF0: Case, Gearing And Planetary Unit Parts

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This transmission motor drives the washer transmission so the tub can agitate and spin. Replaces a worn or failed motor to restore normal drive power and reduce noise or stalling during load cycles. What it does

• Turns the transmission gears that power agitation and spinning
• Restores drive when the washer hums but won't agitate or spin
• Stops slipping, unusual grinding, or intermittent drive failures
• Helps eliminate overheating or burning-odor symptoms from a failing motor

• Disconnect power before beginning any service to avoid shock hazard
• Installation typically requires removing the washer cabinet and accessing the transmission area
• Compare the new motor to the old unit for connector and mounting compatibility before installing

Replacement mounting screw for stand mixer panels, brackets, and trim. Secures internal components to keep parts aligned. Replace if missing, stripped, or rusted.

Fix a stand mixer that won't change speeds or runs at one speed only with this speed control part. Direct fit replacement restores all speed settings.

Small but critical: this groove pin locks the planetary/drive assembly to the mixer shaft so the beater is driven firmly and wobble-free. Replacing a bent or sheared pin restores solid, reliable mixing.

What it does

• Secures the planetary to the drive shaft to transmit torque
• Helps fix beater not-turning, slipping, or intermittent drive
• Reduces wobble or knocking from a loose planetary
• Replaces pins that are bent, mushroomed, or missing

What’s included
One groove/retainer pin (sold individually).

Install notes

• Unplug the mixer; work on a padded surface
• Support the planetary; drive the old pin out with a small punch
• Align holes and tap the new pin in until seated flush—don’t overstrike
• Inspect the planetary and shaft holes for elongation; re-grease if opened

The Retaining Clip is an OEM part for Whirlpool stand mixers. This small but essential part ensures the stability and secure fitting of various mixer components, contributing significantly to the appliance's overall performance and durability. Its primary role is to hold parts in place, preventing movement that could lead to wear or malfunction during operation.

Stand mixers are subjected to a variety of stresses, particularly when mixing thick doughs or other dense mixtures. The retaining clip's integrity is vital in these situations, as it helps to maintain the correct alignment and functioning of the mixer's moving parts. 

Symptoms of a bad Retaining Clip in a stand mixer include:

• Components such as beaters or attachments becoming loose or detaching during use.
• Unusual vibration or noise 
• Difficulty in attaching or detaching mixer attachments  

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Small flat washer used in KitchenAid stand mixer assemblies. Provides proper spacing and load distribution between fastened components.

Fix a stand mixer that won't turn beaters or rotates unevenly. This planetary pinion gear restores smooth rotation when teeth are worn or stripped.

Mixer makes growling noise but beater won't spin? This steel retaining pin locks drive components in place. Moderate repair; disassembly required.

Small rubber sealing washer that prevents leaks at hose and pump connection points. Not a hardware flat washer — this is a functional seal component despite its small size.

If your mixer beater stopped spinning or spins loosely, this agitator shaft assembly transfers motor power to turn attachments. Moderate DIY repair.

Mixer making noise or shaft loose? This retaining ring locks gears in place on the drive shaft. Moderate DIY repair with snap ring pliers required.

If your stand mixer components are loose or misaligned, this grooved retaining pin secures parts together for smooth, quiet operation. Easy fix.

This small replacement clip secures appliance components and helps keep wiring and trim fastened so panels stay flush and parts stay in position. It restores proper fit and reduces rattles or loose pieces. What it does:

• Holds wiring, hoses or trim in place to prevent rubbing or pinching
• Keeps panels and covers aligned to reduce noise and vibration
• Prevents connectors and small parts from shifting during operation
• Helps maintain safe routing of wires and hoses

• Disconnect power (and water if applicable) before starting any repair
• Remove any trim or access panels that block the clip location
• Use needle-nose pliers or a flat screwdriver to remove the old clip and press the new clip into place
• Inspect surrounding harnesses and fasteners for wear while installing