We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Show parts
Usually ships within 4 - 14 days
Fix a washer that won't respond to buttons or start cycles with a new electronic control board. This part restores console operation and cycle selection.
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components. Proper installation is critical for the washer's structural integrity.
Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time.
Symptoms of a bad screw include:
This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment.
Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.
Symptoms of a bad clip include:
This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Rear panel for laundry center units. Replaces damaged, cracked, or missing exterior back panels. Restores proper cabinet enclosure and appearance.
This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
If your laundry center won't power on or has a damaged cord, this power cord replacement restores electrical connection. Simple plug-in repair.
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This assembly includes the dispenser housing along with integrated hot and cold water inlet valves for a top-load or front-load washing machine. It controls the flow of water into the machine and routes it through the detergent and fabric softener dispensers. Replace this assembly if the washer is not filling with water, fills slowly, leaks at the inlet connections, or if the dispenser is not properly directing water to the wash tub.
This is a genuine replacement mounting screw that secures appliance components and panels so parts stay aligned and stable. Installing the correct screw restores proper fit and helps eliminate vibration or loose panels. What it does:
This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.
This part is discontinued by the manufacturer and is no longer available for purchase.
This is the pull-out dispenser drawer located at the top front of a washing machine, used to hold detergent, bleach, and fabric softener in separate compartments. The drawer channels each product into the wash drum at the correct point in the cycle. Replace it if the drawer is cracked, warped, or clogged with residue buildup that prevents proper dispensing of laundry products.
This is a handle used on the washer's dispenser area, typically mounted on the front panel. It allows you to pull open the detergent or fabric softener dispenser drawer smoothly. Replace this handle if it is cracked, broken, or has snapped off, making it difficult to open or close the dispenser drawer.
The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.
Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.
Symptoms of a bad mounting screw include:
This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replacement mounting nut secures panels, brackets, and studs in dryers. Restores tight fit for worn, stripped, or missing fastening hardware.