Parts for Whirlpool WTW5840BC0: 02 - Console And Dispenser Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Control console panel for washers. Replaces cracked, damaged, or faded console housing. Mounts on top of washer to provide access to controls and settings.

Fix a washer that won't spin or drain automatically with this electronic control board. Restores proper cycle control and program functions.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control board serves as the main brain of the washing machine, managing cycle selection, water fill levels, motor speed, and overall machine operation. It receives input from the user interface and sensors throughout the appliance. Replace this board if the washer fails to start, stops mid-cycle, displays error codes, or if buttons and cycle selections are unresponsive.

Rear panel for laundry center units. Replaces damaged, cracked, or missing exterior back panels. Restores proper cabinet enclosure and appearance.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

If your laundry center won't power on or has a damaged cord, this power cord replacement restores electrical connection. Simple plug-in repair.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is the water inlet valve assembly that controls the flow of hot and cold water into the washing machine tub during the fill cycle. It contains electrically operated solenoid valves that open and close in response to signals from the timer or control board. Replace this assembly if the washer is not filling with water, fills slowly, continues to fill when it shouldn't, or if you notice leaking at the water connection point on the back of the machine.

Fix a washer that won't fill with cold water or continuously runs with a new inlet valve. DIY-friendly repair, typically takes 20-30 minutes to replace.

If your washer won't fill with water or fills too slowly, this water inlet valve controls flow to restore proper filling. DIY-friendly repair.

Replacement screw for securing panels, brackets, and internal components. Replaces missing, stripped, or damaged fasteners to restore proper fit.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

The Dispenser Drawer is an OEM part for Whirlpool washing machines. It is responsible for properly dispensing the correct amount of laundry detergent at the appropriate time in the wash cycle. The detergent dispenser drawer is specifically designed to hold laundry detergent pods or liquid in its molded compartments.

Causes of a damaged detergent dispenser drawer can include corrosion or degraded plastic parts over time caused by repeated exposure to laundry detergents.

Symptoms of a malfunctioning dispenser drawer include:

• Improper dispensing or no dispensing of detergent during wash cycles
• Residue buildup or leaks from the dispenser area
• Drawer not opening or closing securely as intended
• Dispenser components broken, cracked, or non-functional

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Drawer is an OEM part for Whirlpool washing machines. It is responsible for properly dispensing the correct amount of laundry detergent at the appropriate time in the wash cycle. The detergent dispenser drawer is specifically designed to hold laundry detergent pods or liquid in its molded compartments.

Causes of a damaged detergent dispenser drawer can include corrosion or degraded plastic parts over time caused by repeated exposure to laundry detergents.

Symptoms of a malfunctioning dispenser drawer include:

• Improper dispensing or no dispensing of detergent during wash cycles
• Residue buildup or leaks from the dispenser area
• Drawer not opening or closing securely as intended
• Dispenser components broken, cracked, or non-functional

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.

This nameplate displays your appliance's brand identification and model information. It's typically mounted on the front or interior of the appliance for identification purposes. Replace this nameplate if it's damaged, illegible, or missing and you need proper appliance identification.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.