Parts for Ge JP656SD1SS: Control Panel & Cooktop Parts

Burner won't turn off or stays on high? This infinite switch controls power to your surface element. Moderate DIY repair restores heat control.

Burner won't heat or stays on constantly? The infinite control switch regulates burner temperature. Simple DIY fix with basic tools in under 30 minutes.

Replace your cooktop's control knob when cracked, broken, or worn. This knob installs on the control panel to adjust burner heat settings precisely.

Replace your range indicator light when it fails to illuminate. Shows when burners or oven functions are active for safety. Verify fit with your model number.

Replace your cooktop's main glass top assembly if the surface is cracked, chipped, or shattered. This complete glass panel restores the cooking surface.

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

• 1 hold-down bracket

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

Warming element not heating? This radiant element restores heat to your warming zone. DIY-friendly repair with basic tools in under an hour.

Burner won't heat or work? This radiant surface element restores your cooktop. Easy DIY fix in about 20 minutes with basic tools. Fits many models.

Element stopped heating or center coil went out? This radiant heating element restores even stovetop cooking. DIY repair in 20 minutes with basic tools.

Mounting bracket that secures the radiant element to your cooktop. Replace if bracket is bent, broken, or missing to properly support the heating element.

Replacement mounting stud for cooktops and ranges. Secures the cooktop assembly to the cabinet or countertop. Replace if broken, stripped, or missing.

Clear protective tape secures glass panels and components on your cooktop. Replace when tape loses adhesion or during glass panel repairs. Confirm fit.

Foam seal tape creates an airtight barrier between your cooktop and countertop, preventing spills from dripping into cabinets. Replace when worn or gaps appear.

Mounting plate that secures and supports the wiring harness in your cooktop. Replace if cracked, broken, or missing to properly secure electrical connections.

ST10-16 X 7/16"

Factory screw secures brackets, panels, trim, or burner components on ranges, cooktops, and wall ovens. Replaces missing, stripped, or corroded fasteners.

Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.

Replacement mounting screw secures panels, brackets, and controls on ranges and ovens. Needed when original screws are missing, stripped, or damaged.

ST10-16 X 7/16"

Black. 8-18 AB HXW 3/8

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage