Parts for Ge JGSP28DEN3BB: 06 - Control Panel & Cooling Fan Parts

Touch pad control panel for ranges. Installs on the front control surface. Replace if the graphics are worn, faded, peeling, or the panel is cracked or damaged.

Replace your range's bottom control panel trim if it's cracked, broken, or missing. This decorative trim piece installs below the control panel area.

Control panel touch pad for your range. Installs on the control panel to provide button interface. Replace if cracked, unresponsive, or worn out.

Oven won't heat or ignitor doesn't glow? A failed control board prevents baking and broiling. This replacement restores temperature control and operation.

Plastic faceplate graphics assembly that covers electronic range controls. Replace if cracked, faded, or damaged. Displays function labels like Bake, Broil, and Time.

Replace a faulty infinite switch when your range burner won't heat, stays on high, or cycles incorrectly. Controls surface element temperature settings.

Burner won't heat or stay at the right temperature? This range infinite switch controls surface element heat levels. Direct replacement part.

This control bracket secures and positions the range/oven control assembly so the console stays stable and the control board is properly aligned. Replacing a damaged bracket restores firm mounting and reliable button/knob operation. What it does:

• Mounts and supports the control board/console to the appliance cabinet
• Keeps the control panel aligned to prevent rubbing, vibration, or mispositioned buttons
• Prevents the control assembly from shifting during use, which can cause intermittent controls
• Helps maintain consistent button/knob actuation and overall console stability

• Disconnect power to the appliance before starting any repair
• Access usually requires removing the console or control panel; keep or note screw/hardware locations
• Handle the control board and wiring gently to avoid connector or component damage

This blower assembly circulates air through the appliance to support drying and venting, restoring proper airflow for consistent performance. It replaces a worn or damaged fan wheel and housing to reduce overheating and poor drying. What it does:

Pilot indicator light mounts in the control panel and illuminates when a surface element or heating circuit is powered. Replace if burned out or stuck on.

Seals the left edge of your range cooktop to the chassis, containing spills and fumes. Replace when worn to restore a clean seal and easier cleanup.

Seals the right edge of your electric range cooktop to prevent spills from entering the chassis. Replace if worn, cracked, or no longer sealing properly.

This front gas-mount gasket seals the oven door/frame to help keep heat and combustion gases inside the appliance, improving efficiency and consistent cooking. It's a direct-replacement part used where a worn or damaged gasket lets heat or fumes escape. What it does:

• Creates a tight seal between the oven door and frame to reduce heat loss and maintain oven temperature
• Helps prevent combustion gases or odors from escaping the oven cavity
• Reduces drafts and uneven cooking caused by a compressed or torn gasket
• Restores proper sealing when the existing gasket is brittle, torn, or flattened

• One front gas-mount gasket

• Turn off and disconnect power; shut off gas supply and ensure the appliance is cool before starting
• Removal may require loosening or removing door/retainer screws or clips; keep fasteners for reinstallation
• Inspect the door and frame for damage and clean mating surfaces before installing the new gasket

Seals the top maintenance panel on over-the-range units to keep grease and steam out of internal cavities. Replace when worn to restore a snug seal.

This limit switch is a position-sensing safety switch used in cooking appliances. It signals the control when a mechanism reaches the correct position, helping the unit start or stop related functions reliably.

• Detects the position of a latch, c

Oven overheating or won't heat properly? This thermal limit switch monitors temperature and cuts power to prevent damage. Resets automatically when cooled.

Black burner trim ring for gas ranges. Replaces cracked, chipped, or discolored trim pieces around stovetop burners. Restores a finished appearance.

Insulation panel that installs on the back and bottom of your oven cavity. Replace if damaged, torn, compressed, or missing to maintain heat efficiency.

Fix burners that won't ignite or spark continuously. This spark module controls ignition for all surface burners. DIY repair in about 45 minutes.

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance component

ST10-16 X 7/16"

This 8-32 pan head screw secures internal components in your range. Replace missing, stripped, or damaged screws to restore proper assembly.

Nickel

Black. 8-18 AB HXW 3/8