Parts for Kenmore 110.25122811 (11025122811, 110 25122811): Controls And Water Inlet Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Rear panel for laundry center units. Covers the back of the appliance cabinet. Replace if cracked, dented, rusted, or missing for complete enclosure.

Number-8, 18-thread mounting screw secures panels, brackets, and assemblies. Replace missing, stripped, or damaged screws to restore secure fitting.

Replacement power cord for laundry centers and washers. Installs at the rear panel to restore electrical connection. Needed when original cord is damaged, frayed, or missing.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness assembly routes power and signals between an appliance's control and internal components so circuits operate reliably. It replaces a damaged or worn harness to restore consistent electrical connections and safe operation. What it does:

• Connects control board to motors, switches, heaters, or sensors depending on model
• Enables proper power and signal flow for normal appliance cycles
• Commonly replaced when controls are intermittent, appliance won't start, or circuits short
• Prevents loose or frayed wires that can cause arcing or failure

• Always disconnect the appliance from power before starting work.
• Verify connector orientation and routing; match harness clips and ties to original locations.
• Inspect connectors and wiring for damage; replace if any exposed conductors or melted insulation are found.

Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.

Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.

Fix a washer that won't advance through cycles or gets stuck between wash and rinse. This cycle switch controls your wash sequence. DIY repair.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This console is the appliance's control panel assembly that houses buttons, knobs, and the user interface so you can choose cycles and settings and read the display. It restores easy, accurate control when the original panel is damaged. What it does:

• Provides the front user interface for selecting cycles, options, and settings
• Holds buttons/knobs and the display used to communicate status and cycle progress
• Common symptom: cracked, broken, or loose panel preventing normal button use
• Common symptom: partially unresponsive or misaligned controls and visible damage
• Works with the appliance's existing electronic controls and wiring harness

• Disconnect power at the circuit breaker or unplug the appliance before any work
• Remove trim or housing screws to access and replace the console; keep fasteners for reassembly
• Handle the display and printed circuit areas carefully to avoid damage from static or impact
• If electronic connectors are present, unplug gently by the connector body (not the wires)

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix a washer that won't fill, fills slowly, or drips when off with a new water inlet valve. Most DIYers complete this repair in 20-30 minutes.

Fix washer display errors, control failures, or electrical malfunctions with this wire harness assembly. Restores power and signal connections. Moderate DIY.

This replacement control knob restores smooth, precise adjustment of a cooktop or range surface burner. Replace a cracked, stripped, or missing knob to reliably turn the burner valve or switch and set the right heat level. What it does:

• Mounts on the burner valve or switch shaft to turn the burner on/off and adjust heat
• Replaces knobs that are broken, stripped, wobbly, or missing
• Helps restore accurate "Off" and heat setting alignment
• Common fix for a burner that's hard to turn or won't adjust properly

• 1 control knob

• Disconnect power; for gas units, also shut off the gas supply
• Pull the old knob straight off the shaft—avoid prying against the panel
• Align the new knob with the shaft orientation and press straight on until fully seated
• Verify smooth rotation and correct "Off" alignment after installation

Replacement control knob for selecting settings on your washer or dryer. Restores secure grip and operation when original is cracked, stripped, or missing.

This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.