Craftsman Lawn Mower Parts

This is a gasket kit that contains a variety of parts utilized in many kinds of lawn and garden equipment. Each of the parts in the kit is created to seal two surfaces inside the equipment. The components in the kit include a carburetor insulator plate, a carburetor gasket, a carburetor insulator gasket, two carburetor gasket plates, an exhaust pipe gasket, a valve cover gasket, and an oil drain plug washer. If a lawn and garden tool is leaking fuel, air, or oil, these parts can be used to replace the faulty component.A socket wrench or small monkey wrench and a screwdriver will be needed to replace any parts included with the gasket kit. Make sure the lawn equipment is on a flat surface and the spark plug wire has been disconnected. Disassemble any needed components to reach the gasket or other part that needs to be replaced. Put in the new component and reassemble before use.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual kit. The external gasket kit is designed to be used with snowblowers manufactured by Yard-Man, Huskee, MTD, Yard Machines, Troy-Bilt, Cub Cadet, and Craftsman.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

The primer bulb is a small plastic piece that will draw fuel from the fuel reservoir and into the carburetor when it is pressed down. This ensures that the fuel can get into the carburetor so that combustion can happen in the engine. If the primer bulb is broken or damaged on the engine, it will mean that the carburetor will not be getting the fuel it needs to get the engine to start. In some cases, the engine might not start at all. Other times, it might take a while to get the engine to start. These could indicate that it is time to replace the bulb. This is an OEM replacement part that is sold individually. It will work with lawnmowers and other types of small engines. The bulb is compatible with a range of different popular brands including Toro, Kawasaki, Cub Cadet, MTD, and Craftsman.

This carburetor is a genuine MTD part. A carburetor is a tube that filters the air and fuel through the valves of the engine. This carburetor works with small engine devices such as snowblowers and lawn mowers. Natural wear and tear from the usage of an engine over a long period of time can cause the individual components within the engine to malfunction or fall into disrepair. The longer that a carburetor is in use without replacement, the more likely it is to become damaged or weakened, which will require a swift replacement. Signs of weakening infrastructure for which the carburetor might be responsible can include an engine that frequently stalls or will not start, a clotted fuel bowl blocked by dirt and gunk that results in overflowing fuel through the engine's vents, a poor ratio of air and fuel that results in wheezing, hissing, or popping engine noises, or a poor ratio of air and fuel that results in black smoke pouring out of the engine. Any of these symptoms in an engine will require the immediate replacement of the carburetor.

This authentic OEM replacement V-drive belt transfers rotation energy from one location to another in a lawn mower or snow blower. They connect to a series of pulleys, and as one pulley turns, the others also turn. This makes the engine more efficient. This belt connects the transmission to the wheels, causing them to rotate and propel the appliance forward. Over time, drive belts begin to fray and will eventually break if left for too long. If the belt breaks completely, the wheels will no longer rotate, making the appliance useless until the belt is replaced. It's best to check the belt before this happens. Replacing the V-drive belt requires a socket and pipe wrench to gain access to the pulley systems. This belt is compatible with lawn mowers and snowblowers from a wide range of brands, including Craftsman, Yard Machines, Huskee, Bolens, MasterCut, Ryobi, MTD, and more. This is a high-quality replacement part that comes sourced directly from its original manufacturer. This belt does not ship with any additional parts.

This replacement part is a seat. It is a genuine replacement part made by MTD. This seat has a low back and is intended for use specifically for riding lawnmowers. This seat is able to support the user while they are operating the machine so that they are comfortable and upright during use.A new seat might be needed if the current one is damaged or missing. It is common for the seat to become worn down over time and lose support. If this is the case, the user might choose to replace it. It is also common that the seat becomes damaged such as being torn or ripped. This can cause the seat to not be as effective.This replacement seat is sold individually. This part is a genuine OEM replacement part sourced directly from the manufacturer.

Husqvarna fuel tank vents are found in several of the chainsaws made by the Husqvarna company. The function of the fuel tank vent is to allow air into the fuel tank. It prevents a vacuum from being created while the fuel is being sent through the fuel line. When the fuel tank vent is no longer functioning correctly, there will be problems with the performance of the chainsaw. This can happen as a result of use and normal wear and tear. If the fuel tank vent malfunctions, a replacement part is necessary.Replacing a Husqvarna fuel tank vent is a simple repair. It requires no specialized tools to complete. Wear gloves and be sure that the chainsaw is cool before starting. Locate the old fuel tank vent on the fuel hose and disconnect it. Put the new replacement fuel tank vent in place.The Husqvarna fuel tank vent is a genuine OEM part. It is supplied directly from the manufacturer. It is sold as an individual piece. The fuel tank vent is made from a high-quality, durable plastic material. It is only compatible with Husqvarna brand equipment. It can be installed in many different models of chainsaws and saws made by the Husqvarna manufacturer.

This is a replacement sprocket for use in various types of handheld lawn and garden tools. It is sourced directly from the manufacturer and is identical to the sprockets found in the original equipment. Sprockets can be used for a range of applications. They are often used as a means to drive the chain around the chain bar on a chainsaw or pruner, for example. The metal sprocket could need to be replaced at some point. Over time, it could start to wear down, or there is a chance that it could bend slightly or corrode. This would reduce its effectiveness, and it could even present a danger to the user. Owners should inspect the sprocket when they are doing routine maintenance and replace it if needed. Replacement of the part is typically simple to do. The sprocket is a genuine OEM part that is sold individually. It is used for chainsaws and pole pruners, and it can be found in some trimmer attachments. It is compatible with certain models from Husqvarna, Poulan, and Poulan Pro.

This bolt is a genuine OEM replacement part sourced directly from the manufacturer. It is designed for use with outdoor power equipment like lawnmowers and snowblowers. This bolt is a hex thread rolling bolt with the nut included. This type of bolt is designed to go into pre-drilled holes, such as on an engine. The hex threads on the bolt push the material through the hole, and the nut is then applied to secure the bolt. Bolts should be inspected as part of routine maintenance to ensure the nut is tightly secured and that the bolt has not rusted or come out. If a rusted bolt is discovered or a bolt is missing from the equipment, this replacement bolt can be used. Before replacing or installing a part on the equipment, allow it to cool and then remove the spark plug from the unit. Gloves should be worn when working with the unit. Install the new bolt and tighten the included nut. This bolt is a hex threaded, 3/8-16 x 1-1/8 bolt made of durable black metal and includes the nut. It is compatible with lawnmowers, snow blowers, trimmers, and lawn tractors manufactured by Husqvarna, Poulan, Weed Eater, Murray, and Craftsman.