Crosley Wall Oven Parts

This oven door glass panel restores a clear, safe viewing window on your range when the original is damaged. Replacing a cracked or shattered pane helps keep heat contained, maintains visibility, and returns the door's appearance.

• Forms the glass window in the oven door to allow viewing while helping contain heat
• Replace if cracked, shattered, loose, or missing to avoid safety risks and heat loss
• Damage can contribute to longer preheat times or poor temperature retention
• Rattling, spiderweb cracks, or sharp edges are common signs it needs replacement

• Disconnect power or switch off the breaker; allow the appliance to cool completely
• Remove the oven door and place it on a padded, stable surface
• Transfer any trim, brackets, handle, and gasket from the original panel; reuse existing screws
• Handle glass with cut-resistant gloves; do not overtighten fasteners; verify door alignment and seals before use

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

This thermostat is a temperature-sensitive switch used in many ranges and wall ovens. It monitors heat and opens or closes the circuit at a set point to protect the appliance and help maintain proper operation.

• Senses temperature at its mounting location and changes state at a specified threshold
• Helps regulate oven heating or activate related cooling/vent components in the circuit
• Common symptoms of a faulty thermostat include no heat, overheating, shutting off mid-cycle, or a cooling/vent fan that won't run or runs constantly
• Electrical diagnosis varies by design; compare room-temperature continuity to your service information

• Disconnect power at the breaker and allow the appliance to cool completely
• Access location per your model; note wire positions and transfer one lead at a time
• Mount in the original location and orientation for accurate sensing; do not bypass the thermostat
• After reassembly, restore power and test operation

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This is a control panel overlay for the electronic oven control on select ranges and wall ovens. It restores clear, readable button labels and refreshes the panel appearance while shielding the control face from everyday wear.

• Provides printed legends/icons for clock, timer, and oven functions
• Adheres to the EOC face to protect it from splashes and cleaning abrasion
• Use when the original overlay is faded, peeling, bubbled, cracked, or illegible
• Model-specific layout ensures the correct key positions and markings

• Disconnect power to the appliance before beginning any disassembly
• Remove the control panel/trim to access the old overlay; retain all hardware
• Carefully peel off the old overlay and clean residual adhesive; allow the surface to dry completely
• Align the new overlay with the display and key openings and apply evenly to avoid bubbles

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This replacement switch restores reliable control of a selected function by opening or closing an electrical circuit inside your appliance. When the original switch wears out, buttons may stop responding or features may not activate consistently.

• Opens/closes an electrical circuit when the button/actuator is engaged
• Routes power or sends a signal to the control or component
• Common symptoms: no response when pressed, intermittent operation, or function won't start
• May show signs of heat damage, loose terminals, or inconsistent "click" feel

• Disconnect power at the breaker before servicing
• Photograph or label wire positions to ensure correct transfer to the new switch
• Move wires one at a time; fully seat connectors on the correct terminals
• Reassemble, restore power, and test the function activated by the switch

This 8-inch surface burner element delivers heat on an electric cooktop or range. Replacing a worn or open element restores even heating on the burner zone and reliable response to temperature settings.

• Heats the 8-inch cooking zone when the surface control is turned on
• Helps maintain consistent pan temperature for boiling, simmering, and frying
• Common symptoms: burner won't heat, heats unevenly or intermittently, visible blistering/breaks in the coil, or scorch marks at the terminals
• Replacing a damaged element can prevent further damage to the receptacle/terminal block

• Disconnect power at the breaker and allow the unit to cool completely
• Handle the element by the bracket; avoid bending the coil
• For plug-in setups, pull the old element straight out and firmly seat the new one; for wired connections, move wires one at a time to the matching terminals and secure properly
• Inspect the receptacle/terminal block and wiring; replace if burnt or loose before restoring power

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

A replacement black control knob that restores a readable, grippable interface for appliance controls so you can select settings confidently. Designed as a direct-fit control knob for compatible Frigidaire appliances. What it does:

• Replaces a broken, cracked, missing, or worn control knob to restore tactile control.
• Provides a clear grip and alignment for selecting heat, cycle, or power settings.
• Helps stop slipping or spinning that prevents accurate setting selection.
• Matches the OEM shape and spline pattern for a secure fit when correct shaft is intact.

• Disconnect power to the appliance before servicing to reduce shock risk.
• Most replacements push onto the splined control shaft; align flat sides or spline grooves and press firmly.
• If the knob does not seat, inspect the control shaft and any retained adapter; do not force the part onto a damaged shaft.

The Range Glass Assembly is an OEM part for Frigidaire ranges. It covers the inner cooking cavity, protecting both the occupant and the heating elements and mechanisms inside. The glass assembly also allows for viewing into the oven to check on food without needing to open the door each time. 

Symptoms of a bad glass assembly include:

• Cracks or breaks in the glass
• Difficulty viewing into the oven cavity 
• Leaks around the glass seal
• The glass popping out of place

Causes of a bad glass assembly can be wear and tear over time, exposure to excessive heat, or damage from impacts. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Relay Board is an OEM part for Frigidaire ranges. It is an electronic component that controls the operation of various range functions and components by directing electrical currents through a network of relays.

Causes of a bad relay board include failure of electronic components over time due to continuous use, component fatigue, water damage, or surges/spikes in electrical current.

Symptoms of a bad range relay board include:

• Inoperable or unreliable oven/range functions such as bake, broil, warm, etc.
• Issues with cooktop burner ignition or flame level control
• Inconsistent or inaccurate temperature readings
• Error codes or diagnostic trouble codes appearing

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This 8-inch surface element kit restores reliable heat on your electric range or cooktop. Replace a failed burner so pots heat evenly and settings respond as expected across your 8-inch cooking zone.

• Heats the 8-inch surface burner for everyday boiling, simmering, and frying
• Replaces a burned-out or damaged element to restore consistent performance
• Helps eliminate weak, uneven, or intermittent heating
• Common symptoms: surface burner won't heat, heats inconsistently, or shows obvious damage

• Disconnect power at the breaker or unplug the appliance before servicing; allow all components to cool completely
• Note wire/terminal positions and transfer any mounting parts from the old element if required
• Ensure terminals are fully seated and the element is properly supported/seated before use
• After installation, test on low and high settings to confirm proper operation

Color: White.

Color: black. Measures about 2 inches in diameter.