Parts for Whirlpool EHT201ZKWR4: 06 - Door Parts

The Bracket-Door Stop is an OEM replacement part for Whirlpool appliances. This zinc-finished bracket is designed to prevent the appliance door from opening beyond its intended range, protecting both the door and surrounding components from potential damage. It ensures the door stays secure and functions smoothly during regular use.

Symptoms of a bad Bracket-Door Stop include:

• The door overextending when opened
• Difficulty in maintaining the door's position
• Visible bending, cracking, or damage to the bracket

Causes of a failing Bracket-Door Stop can include repeated stress from excessive force when opening the door, normal wear over time, or accidental impacts. A damaged bracket can compromise the door's alignment and overall functionality.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures panels, brackets, and other components in your appliance so they stay tight and properly aligned. Use it to replace missing, stripped, or rusted hardware and eliminate looseness, rattles, or gaps.

• Fastens parts to the cabinet/frame to maintain structural integrity
• Helps keep panels and assemblies aligned to reduce vibration and noise
• Replaces missing, damaged, or corroded screws during service
• Common fix for loose panels or components that no longer hold securely

• Disconnect power and shut off water or gas before servicing
• Match length and thread to the original screw for proper fit
• Hand-start threads to avoid cross-threading; tighten only until snug—do not overtighten
• Tighten them evenly to ensure proper alignment

This is the perimeter seal for the refrigerator's fresh food compartment door. It restores an airtight seal to keep cold air in and humid room air out, helping maintain temperature, reduce condensation, and improve overall efficiency.

• Seals the fresh food door opening to prevent air leaks
• Helps stabilize internal temperature and reduce run time
• Replace if torn, cracked, deformed, or not sealing evenly
• Symptoms can include condensation or moisture around the door, warm spots, frost near the door edge, or the door not closing fully

• Disconnect power; allow the door area and new gasket to warm to room temperature
• Soften the new gasket in warm water to relax bends before installation
• Remove the old gasket; seat the new one fully into the channel, starting at the corners—do not stretch
• Use gentle, low heat (hair dryer) to smooth waves; perform a "paper test" around the perimeter and adjust hinges if needed

Specs: 10-16 x 1/2 inch.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This bottom handle end cap replaces a worn or broken cap to restore the handle's finished look and secure the handle trim. It fits the lower end of the appliance door handle and helps maintain a flush appearance and grip. What it does:

• Covers and finishes the bottom end of the door handle for a clean, finished appearance
• Secures handle trim and helps keep the handle aligned during use
• Commonly used when the original cap is cracked, loose, or missing
• Helps prevent sharp edges and reduces the chance of snags on clothing

• One bottom handle end cap

• Designed for a snap- or screw-fit depending on handle style; follow your model's service instructions
• Remove power or secure the appliance as recommended by the manufacturer before working on doors
• Use basic hand tools; avoid forcing the cap to prevent damage to the handle or door

This chrome handle end cap covers and finishes the end of a refrigerator or freezer door handle for a clean, factory look. It restores the appearance of a damaged or missing handle end and helps protect the handle edge from wear. What it does:

• Replaces a cracked, chipped, or missing chrome handle end cap
• Provides a finished, OEM-style appearance at the handle tip
• Helps prevent further cosmetic damage to the handle edge
• Matches chrome trim on compatible door handles for a cohesive look

• 1 chrome handle end cap

• Typically installs by snapping into place or sliding onto the handle; may require removing the handle first
• Use basic hand tools if screws or clips are present; follow your model's service instructions
• Disconnect power only if instructed by model-specific service steps
• Wear gloves to protect finishes and avoid scratches during installation

The Door Handle Kit is an OEM part for Whirlpool refrigerators. It contains both door handles, linkage, fasteners, and installation instructions needed to operate the refrigerator doors. Please note: Handle may be longer, this is a "cut to fit" design. For white order WP2162555. No longer made in almond. Includes both refrigerator and freezer door handles.

Symptoms of a bad door handle kit include:

• Difficulty opening the refrigerator door(s)
• Handles no longer latches the doors securely closed
• Loose, wobbly, or sagging door handles
• Damaged finishes on the plastic handle components

Causes can be normal wear and tear over years of use, brute force twisting of the handles, or issues related to over-tightened door gaskets putting pressure on the linkage.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This door handle spacer sits between the door panel and the handle to set the correct stand-off and support the mounting hardware. Replacing a cracked or missing spacer restores a solid feel, proper alignment, and protects the door finish.

• Maintains the designed gap and stand-off between the handle and door
• Supports and centers the handle over the mounting post(s)/screw(s)
• Helps prevent rubbing, scuffs, or creaks from a handle that sits too close
• Typical symptoms of failure: loose or wobbly handle, uneven gap, rattling, broken or missing spacer

• Disconnect power and, if applicable, shut off water before service
• Support the handle; remove the set screw(s)/bolt(s) and lift off the handle as designed
• Position the new spacer over the mounting point; reinstall the handle and hardware
• Tighten hardware snugly—do not overtighten; check alignment and handle security

This screw anchor is a small plastic fastener that secures panels and trim on appliances, preventing screws from stripping or pulling out. It provides a reliable anchor point for screws where threaded material is thin or absent. What it does:

• Creates a secure mounting point for screws in sheet metal, plastic or thin panels
• Helps prevent screw looseness, stripping, and parts that shift or rattle
• Commonly used to hold trim, panels, or interior components in place
• Works with compatible screws to distribute load and stabilize attachments

• Use the correct screw size and length; anchors are made for specific screw diameters—do not force oversize screws
• Align anchor in the prepared hole before driving the screw to avoid cracking the anchor or surrounding material
• Hand-start screws until seated, then tighten gradually—do not overtighten to prevent stripping or damage
• Disconnect power and follow appliance safety procedures before accessing internal panels

This sheet-metal screw secures appliance panels, brackets, and components to the cabinet. Replacing a missing or stripped fastener restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Fastens sheet-metal parts to the chassis or support brackets
• Replaces stripped, corroded, or lost screws to restore proper hold
• Helps reduce vibration and noise from loose panels
• Maintains alignment of covers, ducts, or trim

• Disconnect power to the appliance; shut off water or gas if applicable.
• Match this screw to the original location and length.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• If the original hole is damaged, repair or replace the mounting point before installing.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This screw cover conceals the mounting screw at the end of the door handle, restoring a clean, finished look while protecting the fastener. Replace a missing or damaged cap to keep the handle hardware covered and secure.

• Covers the exposed handle screw for a finished appearance
• Helps shield the screw head from dirt and moisture
• Direct replacement for a cracked, broken, loose, or missing cap
• Common signs: visible screw, cap won't stay in place, or cosmetic damage

• Use a plastic pry tool to remove the old cover without scratching nearby surfaces
• Verify the handle screw is properly seated; adjust/tighten as needed before installing the cover
• Align the new cover with the opening and press until it snaps flush
• Avoid overtightening the handle screw; excessive torque can prevent the cover from seating

This door trim retainer end cap secures the decorative trim on a refrigerator or freezer door, restoring a finished look and keeping the trim aligned. It helps prevent gaps, rattling trim, and moisture intrusion around the door edge. What it does

• Clips into the door trim to hold the trim firmly in place.
• Keeps door trim aligned to reduce cosmetic gaps and noise.
• Helps maintain a proper seal by preventing trim from pulling away.
• Common symptom: visible gap or loose/rattling trim pieces.

• One door trim retainer end cap.

• Designed for a snap-in replacement; may require a flat tool to pry off the old retainer gently.
• Inspect trim and surrounding clips for damage; replace any broken clips before installing.
• Disconnect power only if working near electrical components; this trim replacement is cosmetic/mechanical.

This part has been discontinued by the manufacturer and is no longer available.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This part has been discontinued by the manufacturer and is no longer available.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Bracket-Door Stop is an OEM replacement part for Whirlpool appliances. This zinc-finished bracket is designed to prevent the appliance door from opening beyond its intended range, protecting both the door and surrounding components from potential damage. It ensures the door stays secure and functions smoothly during regular use.

Symptoms of a bad Bracket-Door Stop include:

• The door overextending when opened
• Difficulty in maintaining the door's position
• Visible bending, cracking, or damage to the bracket

Causes of a failing Bracket-Door Stop can include repeated stress from excessive force when opening the door, normal wear over time, or accidental impacts. A damaged bracket can compromise the door's alignment and overall functionality.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This freezer door gasket seals the door to the cabinet to keep cold air in and humid air out. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and condensation around the door.

• Creates a continuous perimeter seal between the freezer door and cabinet
• Helps stabilize freezer temperatures and limits warm-air leaks that can lead to frost/ice buildup
• Common failure signs: torn or hardened gasket, visible gaps, moisture or ice near the door
• Almond color to match compatible units

• Disconnect power to the refrigerator before servicing
• Warm the new gasket in hot water or with low heat to relax folds, then start at the corners and work evenly around the door
• On screw-retained styles, loosen perimeter screws and tuck the gasket lip under the retainer; tighten evenly
• After installation, check seal with a dollar-bill test and allow up to 24 hours for the gasket to fully conform

This top handle endcap restores the finished look and covers the mounting area on a refrigerator handle. It replaces a cracked or missing endcap to help keep the handle secure and presentable. What it does:

• Covers and protects the top end of the appliance handle and hides mounting hardware
• Restores original appearance when the endcap is cracked, broken, or missing
• Helps maintain a comfortable edge for gripping the handle
• Matches the OEM shape for proper fit and alignment

• Remove the handle per your model instructions before replacing the endcap to avoid damage
• Align the endcap with the handle end and press or snap into place; some models may require fastening hardware
• If hardware is needed, reuse existing screws/clips or your model's parts diagram for the correct fasteners
• Follow all safety guidance: disconnect power and use care when working around doors and heavy parts

The Door Handle Kit is an OEM part for Whirlpool refrigerators. It contains both door handles, linkage, fasteners, and installation instructions needed to operate the refrigerator doors. Please note: Handle may be longer, this is a "cut to fit" design. For white order WP2162555. No longer made in almond. Includes both refrigerator and freezer door handles.

Symptoms of a bad door handle kit include:

• Difficulty opening the refrigerator door(s)
• Handles no longer latches the doors securely closed
• Loose, wobbly, or sagging door handles
• Damaged finishes on the plastic handle components

Causes can be normal wear and tear over years of use, brute force twisting of the handles, or issues related to over-tightened door gaskets putting pressure on the linkage.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This door handle spacer sits between the door panel and the handle to set the correct stand-off and support the mounting hardware. Replacing a cracked or missing spacer restores a solid feel, proper alignment, and protects the door finish.

• Maintains the designed gap and stand-off between the handle and door
• Supports and centers the handle over the mounting post(s)/screw(s)
• Helps prevent rubbing, scuffs, or creaks from a handle that sits too close
• Typical symptoms of failure: loose or wobbly handle, uneven gap, rattling, broken or missing spacer

• Disconnect power and, if applicable, shut off water before service
• Support the handle; remove the set screw(s)/bolt(s) and lift off the handle as designed
• Position the new spacer over the mounting point; reinstall the handle and hardware
• Tighten hardware snugly—do not overtighten; check alignment and handle security

This door trim retainer secures the decorative trim/molding to the door panel, keeping it aligned and firmly attached. Replace a worn or broken retainer to stop loose trim and restore a clean, finished appearance.

• Holds the door trim/molding securely to the door panel
• Maintains proper alignment and a finished look
• Helps prevent rattling, gaps, or edges catching on clothing
• Common symptoms: loose or wobbly trim, trim won't stay attached, missing/broken retainer

• Disconnect power to the appliance at the circuit breaker before servicing
• Support the door and trim to avoid bending or scratching surfaces
• Remove the old retainer and install the new part in the same orientation
• Ensure the trim is fully seated along its length before restoring power