Dryer Cable Or Retainer

This retainer is a small fastener that secures a component inside your appliance, keeping it correctly positioned during operation. Replacing a damaged or missing retainer helps eliminate looseness and noise while preventing wear from parts shifting.

• Holds a mating part or assembly firmly in place
• Restores proper fit when the original retainer is cracked, warped, or missing
• Common symptoms: loose or misaligned parts, rattling/vibration, rubbing noises
• Helps prevent premature wear from movement or chafing

• Disconnect power; shut off gas and water supplies if applicable
• Use your model's diagram to locate the retainer and match its orientation
• Transfer any reusable hardware and ensure the retainer is fully seated
• Reassemble and run a short test to check for proper operation

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

This retainer secures appliance panels and components to keep assemblies aligned and stable, restoring proper fit and reducing noise or vibration. Use when a clip or bracket has broken, come loose, or no longer holds parts in place. What it does:

• Holds trim, panels or internal components in position to prevent rattling and misalignment
• Replaces worn or broken clips that allow gaps or loose parts
• Helps restore a snug fit after service or component replacement
• Works as a simple fastener to maintain proper assembly alignment

• Disconnect power to the appliance before beginning any repair
• Installation typically requires basic hand tools; handle small clips carefully to avoid losing them
• Inspect surrounding clips and mounting points and replace any damaged hardware

This molded wire tie standoff provides a secure anchor point for a cable tie to hold wiring and harnesses away from moving parts and hot or sharp surfaces, helping reduce wear and electrical risk. Fits common HVAC and appliance wiring panels. What it does:

• Anchors wire ties to the appliance cabinet or chassis so harnesses stay routed and secured
• Prevents wires from rubbing on sharp edges, hot components or moving parts
• Helps stop intermittent electrical issues from loose or vibrating connections
• Reduces noise from loose wiring that can vibrate during operation

• One wire tie standoff

• Disconnect power before servicing the appliance to avoid shock or damage
• Mount in the original standoff hole or approved panel location; secure a cable tie through the top loop to hold the harness
• Use the correct fastener or snap method for your model—do not force or overtighten
• If routing or attaching multiple wires, verify clearance from heating elements and moving parts

This retainer is a small mounting clip that secures internal appliance components, keeping parts aligned and preventing vibration or rattling. Replacing a worn or broken retainer restores proper fit and helps reduce noise and movement. What it does:

• Secures a specific internal component to its mounting point to maintain proper alignment
• Keeps parts from shifting or vibrating during operation
• Helps prevent intermittent noise caused by loose fittings
• Supports reliable operation by holding components in the correct position

• One retainer clip

• Disconnect power to the appliance before beginning any work
• Inspect the surrounding mounting area and matching mating tabs for damage before installing
• Install the retainer by aligning it to the mating slots and snapping or fastening it into place; use gentle pressure to avoid breakage
• If other mounting hardware or adjacent parts are damaged, replace them as well for a secure fit

This plastic flat drive belt transmits motion between components to enable proper operation of the appliance. It replaces a worn or broken belt to restore consistent movement and reduce slipping. What it does

• Transfers rotational force from a motor or gearbox to driven parts to power operation
• Restores normal movement when a belt is cracked, stretched, or broken
• Helps eliminate slipping, uneven operation, or intermittent cycles caused by belt failure
• Used where a molded or flat plastic belt is specified instead of a rubber V-belt

• One replacement plastic flat drive belt as shown

• Install only when the appliance is unplugged or the circuit is powered off to avoid shock or injury
• Inspect pulleys, idlers, and related parts for wear and replace if damaged to prevent premature belt failure

This retainer clip secures small appliance components in place to prevent movement and ensure proper alignment for reliable operation. It's a simple replacement that restores lost or broken mounting support. What it does:

• Holds and stabilizes the attached component or assembly to prevent shifting during use
• Maintains proper alignment for connected parts to reduce wear and noise
• Commonly used where a small plastic or metal clip is needed for secure mounting
• Can address symptoms like loose panels, rattling, or parts that won't stay seated

• One retainer clip

• Disconnect power to the appliance before attempting any repair
• Remove surrounding panels as needed to access the clip; small trim tools may help
• Replace the broken retainer with the new clip and verify the secured component is seated correctly