Dryer Plug Or Insert

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.

This reversible door plug covers the unused hinge or mounting hole after changing a door swing, restoring a clean appearance and helping keep out dirt and drafts. Simple, color-matched replacement for a neat finish. What it does:

• Covers exposed hinge or mounting holes on the door edge for a finished look
• Helps block dust, pests and drafts from entering through unused openings
• Matches original geometry to sit flush with the door surface
• Designed to work with reversible door installations where a hole is no longer used

• One (1) reversible door plug

• No tools are typically required; press plug into the unused hole until it seats securely
• Confirm correct orientation before installing to ensure a flush fit
• Inspect surrounding sealing surfaces and clean area before installation
• If plug is damaged or does not seat properly, replace with the exact part number

This white replacement plug fills and finishes an unused opening on the appliance, helping keep out dust and debris while restoring a clean, factory appearance. Use it where a small trim or access hole needs a discreet cover. What it does:

• Covers unused holes or access slots to protect internal components from dust and moisture
• Restores a finished, factory look to trim panels or consoles
• Helps prevent small items from falling into openings
• Simple, low-profile piece that stays recessed and unobtrusive

• No power required; work with the appliance unplugged or power turned off as a safety precaution when accessing trim
• Push the plug into the opening until it seats flush; a gentle push with a finger or soft tool is usually sufficient
• If removal is needed later, gently pry with a flat, non-marring tool to avoid scratching surrounding surfaces

This drum hole plug seals an unused or service access hole in the dryer drum to help prevent clothing snags and reduce interior airflow leaks. Simple replacement restores the drum surface and helps keep items from catching. What it does:

• Covers a drum access/service hole to provide a smooth interior surface
• Prevents fabric from catching or tearing on open drum holes
• Reduces unwanted air leakage through the drum
• Helps maintain normal drum rotation contact points by keeping openings closed

• One drum hole plug

• Disconnect power to the appliance before starting any repairs
• Inspect the drum area and remove any debris before installing the plug
• Press or snap the plug into the hole until fully seated; replace if damaged or deformed

This T-plug electrical connector secures a reliable connection between wiring harnesses and appliance components, restoring proper power and signal flow for affected circuits. It's a direct-fit replacement when the plug is damaged or corroded. What it does:

• Provides a secure electrical connection between the harness and the appliance component
• Restores power or signal to components when a broken or loose plug causes intermittent or no operation
• Replaces melted, cracked, or corroded connectors that can cause poor contact
• Helps prevent arcing and further wiring damage when properly seated

• One T-plug electrical connector

• Disconnect power to the appliance before starting any work
• Verify connector orientation and fully seat the T-plug until it clicks or is firmly retained
• Inspect mating harness and terminals for damage or corrosion; replace harness if terminals are compromised
• Use basic hand tools; follow proper electrical and appliance safety practices

This plastic screw plug covers and protects unused screw holes on appliance panels for a clean, finished look while helping keep out dirt and moisture. Simple replacement to restore appearance and prevent debris buildup. What it does:

• Covers exposed screw holes in trim or panels to improve appearance
• Helps block dust and light debris from entering through openings
• Prevents accidental contact with recessed screws
• Useful when replacing panels or removing components where plugs were lost

• One plastic screw plug

• Disconnect power or unplug the appliance before accessing internal panels when necessary
• Press the plug into the hole by hand; use a flat tool gently if alignment is tight
• Do not force or hammer the plug to avoid panel damage
• Replace any damaged surrounding trim before installing plug for a secure fit

This multi-vent plug seals an unused vent opening to stop unwanted airflow and keep the appliance interior protected. It's a direct-fit replacement designed to restore proper venting and help prevent drafts, debris, and pests. What it does:

• Plugs an unused multi-vent opening to prevent air leakage and drafts
• Helps keep dust, lint, and small debris out of the appliance vent path
• Reduces the chance of pest entry through an open vent
• Restores the intended vent configuration after service or part removal

• Disconnect power or gas to the appliance before servicing for safety
• Install by aligning and pressing the plug firmly into the vent opening until seated
• Do not force if resistance is excessive; inspect for obstructions or damage
• Replace damaged parts before installing the plug

This light hole plug seals the unused drum-light opening in the dryer cabinet. Replacing a missing or brittle plug helps contain lint, limit drafts, and protect internal components around the opening.

• Covers the factory light opening when no drum light is installed
• Helps maintain proper cabinet airflow and lint containment
• Shields the opening from dust and moisture
• Replace if the plug is missing, cracked, hardened, or won't stay seated

• Disconnect power before servicing
• Access the light-hole location per your model's service instructions
• Press the plug fully into the hole until seated flush
• Ensure no wires or components are pinched around the opening

This insert is a small trim and mounting piece used to secure and align adjacent appliance panels and components, restoring a finished look and preventing debris from entering tight gaps. What it does

• Provides a finished edge or trim where panels meet to improve appearance
• Helps align and hold panels or controls in the correct position
• Reduces rattling or movement caused by loose trim or mounting points
• Blocks dust and debris from getting into small openings

• One insert as shown

• Use basic hand tools; avoid forcing parts to prevent breakage
• Disconnect power to the appliance before doing any repairs that require access behind panels
• If multiple trim pieces are damaged, replace matching pieces for a uniform fit and appearance

This replacement plug seals an unused opening on compatible appliances to help prevent moisture, dirt and pests from entering and to restore the original appearance and fit. It's a simple, low-cost part for routine repairs. What it does

• Seals an access hole or unused opening to help keep moisture and debris out
• Helps block pests and contaminants from entering the appliance cabinet
• Secures wiring or tubing routing where a protective cap is required
• Restores original fit and finish at the plug location

• One replacement plug

• Disconnect power to the appliance before beginning any work
• Remove the access panel or trim necessary to reach the plug location
• Press the plug into place; small hand tools may help for snug seating
• Inspect surrounding gaskets and panels for damage while installing