Dryer Drum, Bulkhead, Front Parts

Unusual noises or vibrations during the drying cycle Causes of a faulty lint chute assembly can include normal wear and tear over time, clogging due to excessive lint accumulation, or physical damage due to improper cleaning or maintenance. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dryer models.

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

This bulkhead is the front tub housing that supports the washer drum and seals the washer cabinet to help contain water. Replaces a cracked or corroded housing to restore proper drum alignment and help prevent leaks. What it does:

• Provides structural support for the washer tub and drum assembly
• Forms the front seal surface to help keep water inside the washer
• Helps maintain correct drum alignment to reduce noise and wobble
• A failing bulkhead can cause visible leaks, excessive vibration, or rubbing noises

• Disconnect power and water supply before starting any repair
• Inspect surrounding seals, gaskets, and mounting hardware when replacing the bulkhead
• Replacement may require partial disassembly of the washer cabinet and drum; follow OEM instructions

This is the main drum assembly for a dryer, the large cylindrical chamber where clothes tumble during the drying cycle. It rotates to circulate garments through heated air for even drying. Replace this drum if it has developed cracks, dents, worn spots that snag clothing, or if the interior coating is peeling or damaged.

Replacement dryer drum front bulkhead panel. Installs at the front of the drum assembly. Needed when cracked, warped, or damaged from wear.

The Bulkhead is an OEM component for Whirlpool dryers. As a structural panel, it secures the rear of the appliance while enabling airflow behind sliding doors. 

Formed from durable composite, the lightweight bulkhead installs easily into precise slotted tracks inside the chassis. This allows full retraction during maintenance without removing additional panels. 

Causes of a faulty bulkhead can include cracked welds or screws stripping their anchors from extreme force vibration over many years of use.

Causes of a bad bulkhead can include:

• Noisy rattling and resonance as the dryer operates  
• Restricted door movement from misalignment
• Inability to fully access internal components  
• Excessive ducting leaks from gasket compression failure

Replace yours with this genuine Whirlpool bulkhead to restore smooth, tight operation. Compatible with Kenmore, Maytag, and KitchenAid dryers.

This is the complete drum assembly for a dryer, including the cylindrical tumbling chamber where clothes are placed for drying. It rotates during the drying cycle to tumble laundry through heated air. Replace this assembly if the drum is cracked, warped, has damaged baffles, or if clothing is snagging or tearing during the drying cycle.

Replaces the outer tub cover panel on front-load washers. Protects internal components and maintains drum alignment. Order when cracked or damaged.

This drum wrapper assembly replaces the damaged or worn drum wrap to help the dryer drum turn smoothly and protect clothes from snags and rubbing. It restores a proper drum surface and reduces vibration and noise. What it does:

• Provides a protective wrap around the drum edge to prevent fabric from catching or rubbing
• Restores a smooth drum surface for quieter, even rotation
• Helps reduce drum vibration and scraping noises caused by worn or torn wrapper material
• Supports proper drum alignment and contact with seals during operation

What's included: One drum wrapper assembly Install notes:

• Disconnect power (and gas, if applicable) before starting any repair
• Installation requires partial disassembly of the front panel/drum—follow the OEM service manual or schematic
• Handle the drum and edges carefully to avoid cuts; use gloves and eye protection

Galvanized front bulkhead assembly that forms the dryer's cabinet front panel. Installs to support the door and control area. Replace when cracked or corroded.

This is the complete drum assembly for a clothes dryer - the large cylindrical tumbler where clothes are placed for drying. It rotates during the drying cycle to tumble clothes through heated air. Replace this assembly if the drum has cracks, holes, excessive wear marks, or if clothes are snagging or getting caught during operation.

Front bulkhead assembly for your dryer drum. Replaces cracked, warped, or broken bulkheads. Mounts to the front of the drum for structural support.

Front bulkhead for dryer drum assembly. Replaces cracked, broken, or worn bulkheads. Essential structural component for proper drum support.

This drum wrapper assembly replaces the worn or damaged drum liner that cushions and protects the dryer drum and clothes during tumbling. It restores a smooth drum surface to reduce rubbing and help quiet operation. What it does:

• Provides a smooth, protective lining around the drum to prevent fabric wear and snags
• Reduces friction and rubbing noise caused by worn drum surfaces
• Helps maintain proper drum-to-drum contact and even tumbling
• Prevents direct metal-to-metal contact that can cause marks on garments

• Disconnect power before beginning any disassembly; follow the dryer's service manual for access
• Removal typically requires partial drum disassembly; handle the drum and liner carefully to avoid damage
• Inspect adjacent parts (drum baffles, seals, rollers) for wear while replacing the liner

Front bulkhead for dryer drum assembly. Replaces cracked, broken, or damaged bulkhead components. Essential structural part for proper drum support.

Front bulkhead for your dryer drum assembly. Replace this structural component if it's cracked, damaged, or worn to restore proper drum support.