Parts for Frigidaire FLSG72GCS8: 03 - Dryer Mtr Parts

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A replacement mounting screw used to fasten panels and components in compatible Frigidaire appliances. Replacing a missing or damaged screw restores secure fastening, reduces vibration/rattling, and helps keep parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets or small components to prevent movement and rattling
• Replaces missing, stripped, or damaged fasteners that can cause loose or misaligned parts
• Helps maintain proper fit and finish of appliance panels and access covers
• Useful when a loose screw causes vibration noise or minor part movement

• Unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use the correct screwdriver or bit to match the screw head to avoid stripping
• Start threads by hand, then tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and retain any removed hardware for reuse

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

PPH ab st/z/ch `6 - 18x.60

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

The Blower Wheel is an OEM part for Frigidaire clothes dryers. This component works to propel hot air through clothes during drying cycles.

Causes of a bad blower wheel involve wear from years of operation, such as bearing deterioration or plastic fan blade cracking/warping. Foreign object damage or improper cleaning techniques pose other risk factors.

Symptoms of a bad blower wheel include:

• Slow or weak drying even on high heat settings
• Loud clanking or grinding noises from inside the duct
• The dryer not activating or functioning when turned on
• Reduced air discharge observable at the vent

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small metal mounting screw used to secure appliance panels and internal components. Simple replacement that restores proper fit and reduces rattling or loose parts when the original fastener is missing or damaged. What it does

• Secures panels, brackets, or trim pieces to the appliance chassis
• Holds internal components in place to maintain alignment and function
• Helps prevent vibration noise and movement from loose parts
• Suitable where the OEM listed screw size and thread match the original

• Disconnect power and water before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
• Keep any removed screws organized to ensure correct reassembly

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

The Idler Arm Assembly is an OEM part for Frigidaire dryers. It is an essential component of the dryer's drum support system, responsible for maintaining the proper alignment and smooth rotation of the drum during operation. The idler arm assembly typically consists of an idler arm, pulley, and bearings, working together to support the weight of the drum and facilitate its rotational movement.

Symptoms of a bad idler arm assembly in a dryer include:

• Loud squeaking or grinding noises during operation
• Excessive vibration or shaking of the dryer
• Difficulty in starting or maintaining the drum's rotation
• Potential damage to other components due to misalignment

Causes of a bad idler arm assembly can include wear and tear over time, damage from foreign objects entering the drum, or issues with the bearings or pulley components. A faulty idler arm assembly can lead to improper drum alignment, increased friction, and potential damage to other parts of the dryer.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drum Belt is an OEM part for Frigidaire dryers. It plays a pivotal role in the mechanism of the dryer, connecting the motor to the drum to enable its rotation. Without a functioning belt, the dryer's drum will not turn, preventing clothes from drying properly.

Symptoms of a failing Drum Belt include:

• A dryer that turns on but does not spin
• Unusual noises, such as thumping or squealing, coming from the dryer
• Clothes taking longer than usual to dry
• The dryer stopping unexpectedly during a cycle

Common causes for Drum Belt issues are general wear and tear from regular use, the belt becoming stretched or misaligned, and excessive load sizes that strain the belt beyond its capacity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement power cord restores the electrical connection for compatible Frigidaire appliances so they can safely receive power. Durable insulation and molded ends help ensure a secure, reliable feed to the appliance. What it does

• Provides the main AC power connection between the appliance and the household outlet.
• Replaces damaged, frayed, or burned cords that can cause power loss or unsafe conditions.
• Common symptom: appliance does not power on or loses power intermittently.
• Common symptom: visible cord damage, exposed wires, melting, or frequent tripping of a circuit breaker.

• Always disconnect the appliance from power at the breaker or unplug before installing.
• Inspect the cord routing and strain relief; replace any damaged clamps or covers.
• Tighten terminal connections securely; avoid over-torquing which can damage terminals.

Hex washer head ,10-32 x 0.375. Ground

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

No.12 - 24 x .63 hex head

A replacement union hex nut that secures a refrigerator water line or tubing to a mating valve or fitting, restoring a tight, leak-free connection. Simple, serviceable fastener used on water and refrigeration line unions. What it does

• Secures tubing or line to a mating union fitting or valve to maintain a sealed connection
• Stops leaks at the union when worn or damaged nuts allow seepage
• Helps restore proper water flow to dispenser or ice maker when connection is the cause
• Works with compatible refrigerator water and refrigeration line unions

• One union hex nut

• Shut off the refrigerator water supply before starting work
• Tip: loosen slowly and re-tighten by hand then wrench to avoid overtightening and damaging tubing
• If replacing a corroded nut, inspect the ferrule/sleeve and mating fitting and replace if damaged

This genuine OEM replacement part is a gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential functions. If the dryer is no longer drying clothes effectively, or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is an easy fix.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old valve assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles. 

Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines. 

Symptoms of a faulty ignitor can include:

• The dryer fails to start or stop heating intermittently   
• Cycles taking overly long to complete or feel uneven
• Excessive service calls relating to "no heat" troubles  
• Risk of uncombusted gas pooling in dryer if ignition falters

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Dryer Heat Sensor is an OEM part for Frigidaire dryers. This sensor monitors the temperature inside the dryer drum to ensure clothes are dried effectively and safely by regulating the heat levels during the drying cycle.

Causes of a bad heat sensor can include wear and tear from frequent use, buildup of lint or debris, or electrical issues. A malfunctioning sensor can result in incorrect temperature readings, leading to under-drying or overheating of clothes.

Symptoms of a bad Dryer Heat Sensor include:

• Clothes not drying properly or taking too long to dry
• Dryer overheating or shutting off unexpectedly
• Inconsistent drying cycles
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.