Need Help?
Call
Fix display issues, unresponsive controls, or oven overheating with this electronic control board. Manages bake/broil functions and timing display.
Unplugged oven and removed back panel of oven, found schematics taped to back of oven. Found a relay board that was burned where upper heating element plug connected to it. Replaced relay board and then repaired burned connector by replacing the spade terminal ends that were melted. Suspect connection was loose and that caused board damage. The other board i replaced because some display segments had stopped working with oven temperature. Was difficult to see what temp the oven was. This was a... Read more
Fix E15 errors, runaway oven temperature, or unresponsive controls with this range control board. Manages cooking modes and temperature regulation.
Replaced the control board. Read more
Fix oven lights that won't turn off, error codes E75/E35/F15, or non-responsive controls. This control board restores normal range operation.
If your range displays E15 error codes, won't turn off, or has no oven heat, the electronic control board likely failed. Moderate DIY repair in 1-2 hours.
Stumbled upon Appliance Parts Pros web site and after some research bought 2 circuit boards. (UIB) Interface Board AP4501702 and ESEC Relay Board AP5780950. I carefully replaced the UIB board first and it solved the problem. Things like taking the door off can be found on the internet and took me far more time than actually replacing the board. I have never used APP before but understand that the other board is returnable. I am a very happy and future customer. Read more
Fix F90 error codes, intermittent operation, or unresponsive oven controls. This range control board restores full electronic function to your oven.
NOTHING on the web about my Electrolux slide in range with conv oven. I found a similar oven with video. Video was no help. I replaced the lock motor first, then the oven light switch, worked ok for a short while then F90 fault again. Some guy with a similar oven said he replaced the control unit, so that’s what I did too. So far it works fine. Our range was pretty expensive and still looks new at 11 years old. Hope it keeps working. I have used APPliancepartspros for years for all my problems.... Read more
Range won't heat or display is blank? This electronic control board manages oven temperature, timer, and cooking commands to restore front-panel operation.
Microwave won't turn on, made popping noise, or smells like burned electrical? The noise filter often fails when solder joints arc or short out.
When using the microwave it made a frying sound and completely stopped working. Took cover off (after unplugging) and found filter coil solder joints fried. Took a chance on replacing filter. Works perfectly now. Looking at the solder joints again, under magnification, discovered they were not done properly in the first place. Use caution with cover off, there is a capacitor near the filter that could prove dangerous. Also need tamper proof torx bit to remove 2 of the cover screws, or small... Read more
Fix an oven that won't start, shows error codes, or has unresponsive controls. This main control board restores timing, display, and temperature regulation.
This is the power supply board that provides regulated electrical power to the oven control board and other electronic components in the range. It converts incoming voltage to the levels needed by the control circuitry. Replace this board if the range display is blank, flickering, or if the oven and burner controls are completely unresponsive despite the unit receiving power.
This is a relay control board that manages the power delivered to the surface burner elements on a range or cooktop. It receives signals from the electronic oven control and switches the heating elements on and off to maintain the selected temperature. Replace this board if one or more burners fail to heat, stay on continuously, heat unevenly, or if you notice error codes related to surface element control.
Range not heating or buttons unresponsive? This electronic control board manages all cycle functions and timing. Moderate difficulty repair restores operation.
Range won't turn on or display shows incomplete numbers? This electronic control board manages cycles and user inputs. Moderate DIY repair, 1-2 hours.
With a piece I bought through the store website. The phone attendants are kind, very knowledgeable and the delivery is faster than expected. Read more
Range not heating or responding? This electronic control board manages oven temperatures, timers, and display functions. Moderately difficult repair.
This is a gas burner valve rated for a 12,000 BTU burner on a gas range. It regulates the flow of gas to the burner and includes the mounting screw for secure installation. Replace this valve if the burner won't light, the flame cannot be adjusted properly, you smell gas when the knob is in the off position, or if the valve stem is leaking.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.