Need Help?
Call
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replaced clamp with a new one Read more
Sump hose connects the washer tub to the drain pump. Replace if cracked, leaking, deteriorated, or has holes causing water leaks during wash cycles.
I changed the pump and also discovered the coin trap was wearing thin because it was rubbing against the sheet metal. So I replaced that as well. It took about 15 minutes to remove the coin trap and pump and about 20 minutes to install. The shipping was amazingly fast. I received the parts the next morning. I'm talking I ordered the parts before noon, chose the "fast shipping" option and received parts the next morning around 8:30 AM. Read more
White door handle for laundry center dryer door. Replaces cracked, loose, or missing handles. Restores secure grip for opening and closing the door.
Ordered a new handle from appliancepartspros.com and installed. Read more
Color: white. Measures about 2 inches in diameter.
Replacing the timer, timer knob, dial timer, Read more
Dryer won't start or smells like burning? A melted or loose terminal block where the power cord connects is often the cause. Easy 20-minute repair.
Let me tell you that the videos made by AppliancePartsPros.com are what I needed most. They are simplified and complete. It turned out that because of a loose connection at the power terminal block, it over heated, melting the block and of course frying the wiring and distorting the connections. The erratic power supply must have damaged the control board. I ordered the terminal block and control board and although a little time consuming for a rookie, I got it working first time. I actually... Read more
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
Seals front and rear tub halves to prevent water leaks. Replace if you notice leaking during wash cycles or after bearing repair. Verify fit with your model.
I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more
Washer won't spin or agitate? Humming motor or clothes staying wet often means a failed drive motor. This repair typically takes 15-60 minutes with basic tools.
I took the easy fix first and replaced the Capacitor. That got me three loads before the motor burned out. I ordered the motor from AppliancePartsPros.com after a google search for "best price model # 134159500 Drive motor " The part arrived in 5 days, and it took about 15 minutes to remove the old motor and replace it with the new one. Simple and easy. four screws, four nuts, and two electrical connections. — The hardest step was one of the four mounting screws was way back inside and it took... Read more
Connects washer outer tub to drain pump, channeling water out during drain cycle. Replace if cracked, leaking, deteriorated, or damaged by pests.
Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more
Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.
Pulled front cover off of dryer and back plate to get belt on. Remember to always shut breaker off to machine and test to make sure no electricity is running to it. Pretty simple. I also replaced the seal to the air duct where the lint filter sits since I had to take the front the off anyway. About 1 hr of time to complete and I'll be 60 years old this month. Good thing I didn't have to pull the drum. Read more
Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.
New hose and clamp. Read more
Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:
Dryer overheating or taking too long to dry? This control thermostat regulates internal temperature by cycling the heater on and off. Easy replacement.
I replaced both thermostats, the seals and the heating element and the belt. It's an easy job to keep my dryer last longer. Read more
Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.
I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more
Dryer won't heat? A faulty gas burner assembly prevents proper flame and ignition. This part restores heat for efficient drying. DIY repair in 1-2 hours.
Went to youtube and found out what was the cause. Replaced the parts that said might be the issue, Dryer working perfectly. All done in about 1/12 hrs Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.