Electrolux Washer Dryer Combo Parts

This safety thermostat is a temperature-sensitive switch that helps protect your appliance from overheating. When excessive heat is detected, it opens the circuit to stop power to critical components, helping prevent damage and ensuring safe operation.

• Monitors temperature at a specific location and interrupts power if it exceeds a safe limit
• Can cause no power, no heat, or shutdown during use when failed or tripped
• Helps prevent overheating damage to internal components
• Restores normal operation when replaced

• Disconnect power to the appliance before service
• Note wire positions and terminal orientation before removal
• Use proper tools and avoid bending or stressing terminals
• After installation, check for underlying overheating causes (blocked airflow, failed fan, etc.)

Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.

Replaces cracked, broken, or missing drum baffle that lifts and tumbles laundry inside your washer. Prevents fabric snags and restores proper movement.

Seals the blower housing to prevent air leaks and maintain efficient airflow. Replace if torn, damaged, or causing reduced drying performance.

Spacer that positions and cushions the agitator screw in top-load washers. Replace if worn, cracked, or missing to maintain proper agitator alignment.

Burner orifice that meters gas flow to your dryer's burner. Replace if clogged, damaged, or wrong size for fuel type during LP/natural gas conversion.

Dryer won't turn off or advance cycles? This control timer regulates cycle progression and automatic shutoff. Moderate DIY repair restores timing.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

Converts compatible gas dryers from natural gas to propane. Includes orifices and components for safe LP operation. Order if switching fuel types.

Metal heat deflector that mounts near the dryer heating element. Replace if warped, cracked, or damaged to restore proper heat distribution and protect wiring.

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

Includes bearing and seal. Bearing is not available separately.

Secures the dryer door to the cabinet and provides a smooth pivot point. Replace this hinge if bent, worn, or broken to restore proper door alignment.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

This small metal clip secures the idler pulley to its mounting shaft in laundry center units, maintaining proper belt tension on the drum. Replace if the drum won't turn, you hear rattling noises, the belt appears loose, or if the pulley has fallen off its mount.

This round on/off switch replaces the worn or broken power control on compatible appliances, restoring reliable on/off operation and user control at the front panel. Designed to match OEM fit and function for direct replacement. What it does:

• Provides a simple on/off user control for the appliance's power circuit
• Re-establishes consistent electrical contact when the original switch fails
• Commonly fixes symptoms like no power from the control location, intermittent power, or a switch that won't stay on
• Operates as the primary user-actuated power control for the associated circuit

• One round on/off switch

• Disconnect power to the appliance before testing or replacing the switch to avoid shock
• Verify correct wiring location and connectors before removing the old switch; transfer any wiring harness or connectors exactly
• Handle with care to avoid damage to the switch actuator or mounting tabs