Parts for Mtd 752Z265-JU: Engine Parts

M6 x 1 flange bolt for outdoor power equipment. Secures engine covers, handles, and components. Replace if stripped, rusted, or missing threads.

Engine valve cover cap for outdoor power equipment. Replaces cracked, broken, or missing valve covers on small engines. Direct fit for blowers, tillers, and more.

Complete gasket kit seals engine components to prevent leaks and maintain compression. Replace when rebuilding engine or if gaskets show wear. Verify fit with your model number.

The breather hose is designed as a valve or vent that only functions one way. It allows air into the fuel tank but ensures that no air or emissions escape the tank. When this hose is not functioning, emissions and air could be leaking from the tank and ca

Engine losing power or running rough? A worn cylinder head assembly often causes reduced efficiency. This part covers the cylinder and houses valves.

Fix oil leaks around your valve cover with this engine gasket. Creates a tight seal between cylinder head and cover. Simple DIY repair for small engines.

Replaces a worn, damaged, or missing valve spring retainer in your outdoor power equipment engine. Essential small fastener component for valve assembly.

Fixes engine misfires and rough running caused by improper valve clearance. This adjusting nut helps restore correct valve timing on lawn mowers and tillers.

This replacement part is an external gasket kit, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This gasket kit is different from typical gasket kids as they are used on the external side of the engines. These gaskets are still very important to the engine as a whole and allow it to run smoothly during use.A new external gasket kit might be needed if the current one is broken or damaged. If there are noises coming from inside the machine it is possible that the parts of the gasket are out of place or could be malfunctioning. Be sure the engine of the appliance is completely powered down and cooled off before replacing the gasket kit as this area can be hot from use.Be sure to reference the specific user manual prior to beginning this repair. Note that this is a genuine OEM replacement part and is told individually. This part is sourced directly from the manufacturer.

This is an MTD rocker arm. The rocker arm works in conjunction with the engine and head. The job of the rocker arm is to push the intake valve open, allowing fuel and air to enter the cylinder. Since the rocker arm is a part of the head gasket system, any

Engine running rough or making ticking noises? A worn rocker arm stud can affect valve timing. This replacement stud restores proper valve operation.

If your engine runs rough or won't start, the exhaust valve adjuster may need replacement. This part ensures proper valve clearance for optimal performance.

Exhaust valve spring installs in small engines to control valve operation. Replace if spring is broken, weakened, or missing to restore proper valve function.

Fix engine performance issues or loss of compression with this valve spring. Common in lawn mowers, snow throwers, and other outdoor power equipment engines.

Seals the intake valve to prevent oil leaks and maintain proper compression in small engines. Replace if you notice oil consumption or performance loss.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and depen

Replace your snow thrower's muffler assembly if it's rusted, cracked, or damaged. This exhaust component directs fumes safely away from the engine.

Seals the muffler connection on small engines to prevent exhaust leaks. Replace if you notice excessive noise or exhaust smell. Verify fit with your model.

M8 hex nut secures components on outdoor power equipment engines. Replace if stripped, corroded, or missing to properly fasten parts during repair.

M6 x 110mm carburetor mounting stud for small engines. Secures carburetor to engine block. Replace if stripped, corroded, or missing to ensure proper installation.

Flange bolt fastener for outdoor power equipment. Secures components throughout engine and chassis. Replace if stripped, corroded, or missing.

Fix rough idling and poor fuel mixture with a new carburetor insulator gasket. Prevents air leaks that affect engine performance. Simple DIY repair.

This carburetor insulator is a genuine MTD replacement part for appliances with small engines, such as lawn mowers, lawn tractors, lawn trimmers, snowblowers, chipper shredders, tillers, and leaf blowers. The function of a carburetor insulator in a small

Seals carburetor to insulator plate, preventing fuel leaks. Replace when worn, cracked, or torn to restore engine efficiency. Verify fit with your model.

Carburetor assembly for snow thrower engines. Installs on the engine block to mix air and fuel. Replace if cracked, damaged, or leaking fuel.

Seals between carburetor and engine block to prevent air and fuel leaks. Replace if engine runs rough, leaks gas, or loses power. Verify fit by model.

It's best to have spare O-ring gaskets on hand to rebuild a carburetor when the need arises. Use this manufacturer-approved replacement part to complete the process. When outdoor power equipment shuts off just after starting or won't start altogether, t

Replacement fastener nut for lawn and garden equipment. Threads onto bolts to secure parts together. Replace if stripped, corroded, or missing.

Creates a leak-proof seal between the fuel drain plug and tank. Replace if you notice fuel leaking from the drain area. Verify fit with your model number.

Seals the fuel bowl to prevent leaks and keep dirt out of your fuel system. Replace when cracked or leaking. Confirm fit with your model number.

Engine cylinder head gasket seals the combustion chamber. Replace if you notice oil leaks, overheating, or loss of compression. Confirm fit with your model.

Push rod kit for small engines. Installs in the valve train assembly. Replace if rods are bent, damaged, or worn from normal engine operation.

Piston ring set seals the combustion chamber in lawn mower, snow thrower, and tiller engines. Replace when compression drops or oil consumption increases. Verify fit with your model number.

Oil fill plug assembly for small engines. Seals the oil fill opening to prevent leaks. Replace if cracked, stripped, or missing to maintain proper seal.

Metal connecting rod assembly that links the crankshaft to the piston in small engines. Replace if rod is bent, cracked, or damaged from wear or impact.

Governor arm shaft for small engines on lawn and garden equipment. Connects governor assembly to carburetor. Replace if worn, damaged, or broken.

Engine won't start or runs rough? This camshaft assembly converts rotational motion to reciprocal motion for proper engine operation. Moderate DIY repair.

Engine won't start after sudden stop? A sheared flywheel key breaks the connection between crankshaft and flywheel. Simple DIY repair.

Engine surging or racing? Replace a worn governor gear and shaft assembly. Critical for speed control on small engines. Moderate DIY repair.

Crankcase cover for small engines. Protects internal components from debris and damage. Replace if cracked, broken, or missing to maintain proper engine protection.

Prevents oil leakage in snow thrower engines. Replace if you notice oil seeping during or after use. Verify fit with your model number before ordering.

Replacement oil drain plug for outdoor power equipment engines. Installs in the oil pan to seal the drain opening. Replace if stripped, cracked, or leaking.

Engine oil seal prevents oil leaks in snow thrower engines. Replace if you notice oil seeping around the crankshaft or engine case. Verify fit with your model.

Oil drain plug with washer for lawn mowers and outdoor power equipment. Replaces cracked, stripped, or missing drain plugs to prevent leaks.

Replacement flywheel for small engines. This rotating wheel component stores rotational energy. Order a new one if yours is cracked, rusted, or damaged.

Fix engine overheating issues with this cooling fan. Keeps your small engine running at proper temperature. Direct replacement part for reliable operation.

Engine won't start or pull cord slips? This starter cup connects the recoil mechanism to start your engine. Simple bolt-on replacement part.

Fastener nut for outdoor power equipment. Secures components in place during operation. Replace if stripped, corroded, or missing to restore assembly.

Flat washer for engine recoil starter assembly. Replaces worn, missing, or damaged washers during recoil maintenance or repair. Ensures proper spacing.

Flange bolt for lawn equipment and outdoor power tools. Secures engine components and assemblies. Replace if bolt is stripped, missing, or damaged.

If your snow thrower won't start or the pull cord snaps back, the recoil starter assembly likely needs replacement. Moderate DIY repair in 30-45 minutes.

Snow thrower won't start when you pull the cord? A broken or loose starter handle prevents engine starting. Easy 10-minute fix for most models.

Fix engine surging or racing issues with this throttle spring. Closes the throttle valve to control fuel flow. Quick DIY fix for stuck throttles.

The governor rod is a genuine replacement part found on select models of snowblowers. This rod is responsible for connecting the throttle cable and throttle body, helping to open and close the throttle to change the speed of the engine. This durable metal

This is an authentic OEM replacement part sourced directly from the manufacturer for use in various small engines. This oil fill tube assembly is part of the oil delivery system. This tube delivers the oil to the oil tank when it is added to the engine. I

Engine runs too fast or won't maintain steady speed? This governor bracket controls engine RPM. Common repair for speed control issues on small engines.

Engine o-ring gasket seal prevents oil and fuel leaks. Replace when cracked, flattened, or leaking. Verify fit with your model number before ordering.

Engine dipstick o-ring seals the oil dipstick tube to prevent leaks. Replace if cracked, hardened, or leaking oil. Verify fit with your model number.

Secures fuel, oil, or coolant hoses on small engines. Replace if cracked, corroded, or causing leaks. Confirm fit with your engine model number.

Snow thrower won't start or cranks slowly? This electric starter restores reliable starting in cold weather. Moderately difficult repair for most DIYers.

Replacement shield cover for blower housing. Installs over the blower assembly to protect internal components. Order a new cover if yours is cracked or missing.

Replaces a cracked, hardened, or broken primer bulb on gas-powered engines. Installs on the carburetor to inject fuel for priming before starting.

Fix fuel leaks or loose carburetor connections with this fuel bowl mounting bolt. Secures the fuel bowl to prevent sediment clogs. Quick 5-minute fix.