Parts for Kenmore 665.13009N511 (66513009N511, 665 13009N511): Fill, Drain And Overfill Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Fix a dishwasher not filling with water by replacing the water level float lever. This lever regulates water levels and prevents leaks. Easy 15-minute DIY repair.

Delivers water from supply line to dishwasher tub. Replace if cracked, leaking, chewed by rodents, or damaged during installation or moving.

Fix continuous water flow or dishwasher overflow issues. This inlet valve controls water entering your dishwasher. Easy DIY repair with basic tools.

Seals the water inlet connection to prevent leaks where water enters the dishwasher tub. Replace if you notice moisture damage or leaking at the valve inlet.

Secures water inlet tubing to create a leak-resistant seal. Replace if cracked, stripped, or unable to hold the line securely. Confirm fit with your model.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix dishwasher not filling with water or slow fill issues. This inlet valve controls water flow into your dishwasher. DIY repair typically takes 15-30 minutes.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Carries wastewater from your dishwasher to the household drain. Replace if cracked, punctured, or leaking. Installs at pump outlet and drain connection.

Fix dishwasher overflowing or leaking from the door with a water level switch replacement. Monitors water level during wash cycles. Video guide available.

Fix dishwasher leaks from the tub floor with this overfill protector housing. Guides the float and positions the switch actuator to restore protection.

Fix dishwasher overfilling or leaking issues. This float assembly monitors water level and signals when to stop filling. Simple DIY repair.

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

This kit includes hose clamps and fasteners used during dishwasher installation to secure the drain hose and water supply connections. It ensures tight, leak-free connections between the dishwasher and household plumbing. Replace this kit if you notice water leaking at hose connections or if clamps are corroded, broken, or missing during a new installation or reinstallation.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.